Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Noted that the new V15 SDK for IAR does not have linker config file set correctly on ble_app_blinky_pca10040e_s112 project. The .intvec start location was set to 0x19000 and...
Hi all ,
i'm using nRF51 DK ,im getting issue while program downloading on flash .Program compiled correctly(no any error) even it show flash downloaded but the application...
Hi There,
I have been looking into how to connec my QSPI NOR Flash to the NRF52840.
I have notivced a discrepancy between the comment in the Table 3. of the OPS and the...
Hi,
I have a peripheral which sends data to the central and from central i n eed data to be send to Mobile App
is it possibe to do and how???
or any other ideas you...
I am using Keil 5.24.2
I already downloaded and compiled with build_all the micro_ecc. Having no issues here.
According to the error, and what I read in another thread...
I have been investigating the possibility of using the QSPI external flash peripheral on our NRF chip. After doing a typical qspi read command, the external flash chip would...
Hi,
when i make a connection to my device i get 4 `BLE_GAP_EVT_CONN_PARAM_UPDATE`.
If i make an action of read or write when update event occures i get a duplicated read...
Greetings,
Here's an implementation of controlling the color of a RGB LED with a TIMER of nRF51. It works well most of the time, although it inverts polarity kind of randomly...
Hello,
I am using a Nrf52382 custom board and want to know the Vbattery so I used below code
#define MIN_BATTERY_ADC_VALUE (int16_t)11295 //(min_voltage_on_analog_pin...
Hi,
We have developing ble mesh network using nRF52 mesh sdk is 1.0.1. We have large amount of sensor data it near about 24-25 kb and want to send this data to other node...
I have an application that has been built using Arduino boards and shields for prototyping, and software developed using their IDE...all works fine.
The device comprises...
Hi all,
I am trying to use the SAADC to measure battery level. I have a rechargable lithium battery connected to my customed PCB with a NRF52832. The rechargable battery...
Hello. I have as question about the sd_ble_gatts_hvx. According to the API documents, the call to sd_ble_gatts_hvx will return NRF_ERROR_FORBIDDEN in the following situation...
Utilizing two nrf52832 dev kits, both flashed with v6 of the SD and using V15 of the sdk.
Using two examples from the SDK, the ble_peripheral/ble_app_rscs and a slightly...
