I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hi
I am working on a firmware which can be used in serveral custom boards. While it works perfect in old sdk, I met the following problem when migrating from Sdk 12.2 to...
Hi,
I have tho following configuration: SDK 10, S110 and I'm using Segger Embedded Studio, single banker dfu.
I am able to program DFU and buttonless DFU; However, when...
Hi all,
I am using PCA10040 with nRF5_SDK_13.0.0 and using the ble_perpheral -> ble_app_uart example.
I am trying to stream data from UART to an android phone and the...
Hello,
I've been using the new power profile kit and I seem to be getting only 3 volts output as opposed to the previous versions where I was getting about 3.6 volts. How...
I was checking out the serial example using two PCA10040 evaluation boards. Most of the commands were executed successfully as mentioned in the link http://infocenter.nordicsemi...
Hi,
I'm developing a node based on the nRF52840-QIAA rev. B.
I'm using Eclipse Neon and GCC-toolchain for coding. Softdevice is S140 5.0.0.2 alpha and SDK is V14.2.
...
Hello,
I would like to be able to sample an analog voltage signal with a sample rate of approximately 250us (4096 samples/sec). I am using the SAADC example in nRF5 SDK...
We are trying to use nrfjprog.dll in a c# program to help us with manufacturing and quality assurance.
We are able to load and call the functions from c# and all the functions...
Hi! One of the designs still has the internal RC for the low frequency clock. Hardware and software turns out to be working okay, where system off current is ~0.4uA and sleeping...
Hi,
our BLE device has a hard current limit around 1mA. This is no problem as long as the BLE central behaves as "intended", e.g. iPhones use mostly connection intervals...
Hi All,
I am just play with nRF52 SoC.
We design small wearable device based on MDBT42V BLE module with nRF52832 chip inside. For lear we have nRF52 DK.
I work with...
Is there a way to erase/format everything that is stored in FDS so the storage can be reset to a blank state?
I wasn't able to find away to enumerate all files stored in...
I just updated the latest SDK in keil.
Now I am getting this error.
softdevice_handler.c is v2.0.0-2.alpha
Line 388:
p_ble_enable_params->common_enable_params...
Hi,
I'm missing something on how forwarding interrupt control between SoftDevice and APP works! how is it that part of the interrupts are handled by the SoftDevice code...
