I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I am working on the safety-critical system, I have, ON and OFF function, the entire system using UART communication. In which I am using the nrf_queue() and push the data...
Hello everyone,
I have been using nRF52832 module from Raytac ( link ) for my circuit and I got a trouble with sending advertising packages to other master devices. I installed...
Hi,
I am trying to merge working code that places the microcontroller in system_off when a switch connected to pin 16 is opened. It then wakes up the micro controller when...
Hi, I am working on application where I need to store some bigger files. I chose to use sdcard, but I get weird behaviour. Some sd cards, this looks like totaly random ones...
Hello,
I am playing around with the Blinky example on my custom board, where I have one button and two leds. Everything works fine and I can control the LED2 and detect...
I am using the nRF52832 chip with an SDI connected microSD device. I am able to communicate with the microSD card formatted as FAT32, store data, read data all with the FATFS...
I made my own board in which nRF9160 is populated. It's connected to JLink through SWD. SWO is not connected.
I tried rtt debugging and seems to work correctly, but I'm...
Hello,
I am trying to include bsd.h to my project.
simply typing '#include <bsd.h>' is not enough. I need to add directory 'nrfxlib' but I have no idea how to do that...
Dear Support Team,
We are working on nRF52832 based custom design. We had interfaced 3 different sensors (i.e. one with SPI and 2 with I2C bus mode) and sending continuous...
I am facing a strange situation with my app. After turning off all my peripherals and switching to the most minimal code, I see quite a lot of current consumption and that...
So I'm completely new to bluetooth and I've been trying to set up the nrf52 dk pc 10040, but I can't seem to find any recent tutorials to set it up and I don't know where...
I am running flash_fstorage_example on the nRF52840 DK with SDK 15.0.0
I am having some problems with the example, as below:
1. When I run the example and use the shell...
Hi, I am trying to do MQTT disconnect, but I am always getting an error. First I successfully connect to the MQTT server, then I send some data, and then I want to disconnect...
Hi, I've been trying to use the nRF52840 Dongle to act as Bluetooth 5.0 peripherals but I cant seem to configure them for Long Range (coded PHY) detection. I am currently...
I ran one of my 9160 DK boards for 10 days using the Asset Tracker demo. The Hologram SIM card site I used says data exceeded 1 MB, which I understand the limit. Although...
