Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
I am trying to figure out a way to secure my DFU (via BLE) such that someone cannot sniff the and copy my hex code (and decompile). I cannot use Pairing or Bonding as that...
I can use "Pack Installer" to copy example from Keil folder to my hard disk driver, for instance, I copy ble_app_cts_c to my personal folder.
I can build and flash ble_app_cts_c...
Hello there, I have been trying to look at the documentation and the forum but haven't been able to understand the difference between BLE stack event and SYS event. Could...
Hi,
I have a the nrf51822 chip on a custom board and the ble_hrs code loaded on it. Now I would like this custom board to behave as a beacon with the hrs code sending data...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
ble_app_uart_c2.rar
I want to connect two PCA10001's together, one with the ble_app_uart for s120 using sdk 8, and one with the experimental_ble_app_uart for s110 using...
There's no question, I'm just posting this here in the hopes that it helps someone else out.
After I upgraded my Keil packs to the newest SDK (v8.1.0), my OTA FWU bootloader...
I have a problem getting both mesh and persistent storage to work. I am using the code from github.com/.../nRF51-ble-bcast-mesh and followed the document integrating_w_SD_apps...
Hi,
I am using
HW: nRF6310 + PCA10005
SW: s120_nrf51822_1.0.0_softdevice.hex + ble_app_multilink_central (\Keil\ARM\Device\Nordic\nrf51822\Board\nrf6310\s120\experimental...
Hello,
I am a newbie in in using BLE and exploring the nrf8001 DK. I was able to flash PCA 10000 module with updated firmware and it was detected in the master control...
Hi,
I want to read data ,wich is sent from beacon ,using usb dongle,and after this ,I want to send data received from beacon to pc through serial port.
Exist any example...
Hey.
I am wondering if there is a way to disconnect a slave from a master based on the strength on the connection and not when they naturally loose connection.
To give...
How do I block Bluetooth signals ? (I want the signals to be transmitted 180 degrees, not 360 degrees)
I have read it could be done with aluminium foil, but I have not...
I am looking at using an nRF51 in a BLE product (industrial applications).
One of the things that I have to sort of prove is that it will be a better choice than something...
