Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Is TLS_HOSTNAME socket option supported inside the modem firmware or bsdlib?
When I make the function call:
returns with err==42.
I need to set this socket option...
I have a project that I've joined recently that is based on SDK12.1. The bootloader does not seem to work when compiled with a currently arm-gcc version (9.2.1). It does work...
Hello,
I have a small test BLE peripheral application with a few functions I can invoke over a UART dialog. With one function, I can print the first peer in the peer manager...
Hi,
I'm using the ble_app_uart example as a starting point for my project. Basically I want to program the nRF52 DK to receive data from another device via UART, store them...
For either the nrf52840 or the nrf52833 which pins are responsible for configuring the serial preference SPI, UART and I2C and how to map them. Are they any software examples...
Hi,
i am working with nRF52840-DK and i want to implement a network with below futures
The node(means nRF52840-SOC) Should work as a listener
1. the listener should...
Hello,
I'm getting started with nRF Connect SDK. I've installed the toolchain and SEGGER through Getting Started App (because for some reason the Toolchain Manager froze...
Good day,
I have done DFU using the secure bootloader example in sdk16 using the nrf connect app. The DFU process completes successfully and the controller runs the new...
Good evening, I'm looking for a Blue Tooth BLE Low Energy for Low Power application.
This application should consume few mA only when the controller will be in TX and so...
Hi,
Could I get clarification on if the USB peripheral is isolated and won't backfeed?
In my product, VDDH & VDD are powered via a DC adapter that can be unplugged while...
Hello,
I continue to deal with Zigbee and I have another question. I use 2 nRF52840 chips. First nRF as a Zigbee Coordinator (CLI in SDK\examples\zigbee\experimental\cli...
Hi Team,
We are planning for use the NRF52832 Module for our development, In that for Secure data storage exchange we are implemented the some of the crypto mechanisms...
Hello,
When operating the Thingy91 in poor network connectivity environments, the call to getaddrinfo will sometimes block and eventually timeout returning a error code...
Hello,
I am using the nRF52840_DevKit and SDK-v16.0.0. I am planning to build and flash a bootloader with NRF_BL_DEBUG_PORT_DISABLE set to 1, which means APPROTECT and...
Hi,
I'm using SES v4.52b, a nRF52832 module (BL652) and nRF5 SDK 16.0.0. I'm trying to build a generic SPI Read and Write functions with the following:
The device I...
