I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello,
I'm seeking some clarification on a few points to determine the performance of the nRF52840 in high density deployments. The current intended soft device is S140...
Hello,
in the current project we use a large array (16kB) in RAM to store data. After a reset we would like to check if the array is not corrupted to continue processing...
Dears,
I'm using nrf52832 with PCA10040 and SDK 16.0.0,I want to make a DFU via uart. So used the firmware provided in the SDK(nRF5_SDK_16.0.0_98a08e2\examples\dfu\secure_dfu_test_images...
Hello,
I would like to evaluate nRF9160 for incoming project.
I have Nordic Thingy:91 with iBasis sim card.
Unfortunately, during configuration it turned out, that...
Hi,
We are using nRF9160 for our application and need to design power supply with battery management IC for it and need to know how much power it will consume with all...
Hi,
I would like to setup my nRF52840-Preview-DK as a central to communicate with a peripheral device via UART over BLE.
Once my peripheral device is connected it writes...
I try to connect NRF9160 dev kit to LTE/NBIOT. But device cannot connect to the LTE/NBIOT network. I am using the at_client example with nRFconnect v3.3.0 LTE link monitor...
I have successfully managed to both provision and configure the simple:_on_of_client.
but i'm having troubles configuring the simple_on_off server. I really have no idea...
Hi folks,
I need of your help. I've developed a new custom board with the nrf52840 CKAA ball assignment and I'm having problems on programming it.
I've developed my...
I am getting errors when initializing the Peer Manager in my code. Here are the items that are unique to my setup:
1) I have a thread which uses fstorage to store a single...
Hi all,
Using the nrf52832 TWI, I am trying to interract with a sensor through I2C.
On the same board, I am successfully able to exchange data with an accelerometer...
Hi Everyone
I have an nRF9160 DK v0.8.2 and I'm running the asset_tracket sample.
I'm from Portugal so iBasis sim card doesn't work here. So I went to Spain and tried...
Hi Guys, trying since some weeks to develop an " simple " Gap advertising with only 2 "service Data" ( battery level and an ID of 4 bytes with an uuid of 128bits with Mbed...
Hello.
I run a project on RTOS base on embOS of Segger. Now I want to add a BLE task base on Nordic BLE peripheral UART. As a standalone project not on RTOS it is run O...
