Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I have some trouble using TWI : the slave device connected to nrf52 sends an ack signal (seen on scope) but the i2c handler raises an incorrect address error and discards...
Hi,
The device I am using is nRF52840, WLCSP package. Most of the analog IN pins are noted "low frequency I/O only", e.g. pins A5, A6, C7, C8. - I know there are some exceptions...
Hi,
As of now we are using SEGGER Embedded Studio for compilation and Flashing.
Now we would like to copile using Cmake tool, can you please provide template Cmake for...
downloaded thingysdkv210 from thingy website. extracted that file and executed Prerequisites as per the procedure
downloaded Python v3.xx.xx
downloaded Git v2.xx.xx
...
Hi,
I am trying to add CLI Command feature into the example Open_bootloader_usb_mbr, but get error during link stage when compile as below,
Building ‘open_bootloader_usb_mbr_pca10059_debug...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I am using multiple interrupts. For example, BLE communication interrupt and SOC interrupt. I set the priority of each interrupt...
Dear Sir,
I have flashed 'ble_app_hrs' code to one of my RIGADO DK.
I have installed nRFConnect App in mobile phone.
When I press the scan button I could see the device...
Ok I am using GPIO interrupt and want absolute power saving but when I set the GPIO_INTERRUPT_HIGH_ACCURACY to true it works fine but when I set GPIO_INTERRUPT_HIGH_ACCURACY...
Hello,
I want to use P0.27 as output but no way to get it working (tested on my custom board and on DK). If I just change for another pin to check my code, it's OK.
It...
Hi,
I am using nRF SDK v16 with nRF52DK (pca10040) development board.
I've chosen to use RTT logging and I can see my app logs in JLinkRTTViewer window --- however, I...
Hello!
I am developing a FreeRTOS application for nrf52832 with S132 Soft device
Recently I ran out of ram and checked the map-file for clues. The large posts in the mapfile...
Hi,
I don't understand why the characteristic FitnessMachine Feature : (0x2ACC) is not decoded as a bit field by nRF Connect
I can read it and i can see the good value...
using nRF51-DK
I'm a noob and currently trying to implement a custom service by modifying the 'Heart Rate Service' example which inclued the 'BAS' which is battery status...
Hello All,
I am working on the NRF52810 board with 15.3 sdk in segger IDE.
I have implemented fds with 2 key with 1 file id to store data.
I am storing 2 - 3 1 byte...
