I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
While going though the Makefile of the FreeRTOS HRS example in SDK 16.0.0, I noticed this part:
By default, link time optimization (LTO) is not enabled.
If I enable...
After Christmas update we are unable to use DFU from Android devices.
We've been using such function on a regular basis with our devices and everything has always been fine...
Hello everyone,
I'm using a NRF51822 as a central device, I connect to a peripheral (NRF51822-based device), then I stop the scan. At a later time I initiate another scan...
Hi,
I am trying to program nRF52832 custom circuit with nRF52 DK, I have connected debug out from the nRF52 DK to the custom circuit containing nRF52832 debug in. When I...
Hey Guys,
i am currently experimenting with the NFC functionality and have an issue with our "nrf52840-DK" boards:
i am testing with IAR (8.40.2 - including the library...
Hi there,
I'm trying to use serial library from SDK to interact with cellular modem (AT commands, not nRF9160). I've read documentation (library description, api). May be...
I have build and flashed the zephire/sample/bluetooth/hci_uart on nrf52840 board and connected the board with ubuntu but hci interface was not created when checked using hciconfig...
Hi,
We have chose LCD which has only 3-Wire support CS, CLK and DI so we have connected that pins with nRF51822 chipset. Now Please see the below image which shows that...
Hi All,
I want to read/write long characteristic (200 bytes max) from Android to my device.
I'm working on the 15.2.0 SDK and S140 Softdevice.
I read some Q&A on...
Hi there,
Right now I am doing some dry research into long range Coded PHY for S=8 or S=2 since I need to have some extra room in the link budget to go the distance. The...
Hi, I'm trying to adapt the ble_gateway example for nRF91dk to use a nRF52 instead a Thingy52. When I change the UUID at ble.c from Thingy to nRF52, I'm not able to get a...
Hello guys,
In next few months I've to put down a new design for a medical product. Both nRF52840 and nRF5340 would fit well the application requirements. But I think this...
I want to use two UARTS ie uart0 and uart1. I read that nrf51822 gpio pins can be set as rx & tx but i couldnt find any example.
I am using SDK12.3
Please attach some...
Hi,
I've looked around the DevZone for answers to this, and haven't quite seen an answer, so I'm going to post my solutions here.
I am using the secure bootloader from...
