Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
I am developing AoA for nRF52833.
Please tell me about antenna switching.
Setting:
PSEL.DFEGPIO[0]=28 PSEL.DFEGPIO[1]=29 PSEL.DFEGPIO[2]=30 PSEL.DFEGPIO[3]=31
SWITCHPATTERN...
Hi folks.
recently I've been experimenting with the nrf7002dk Development Kit, and I'd like to move forward with prototyping a custom board around the nRF7002 + nRF5340...
Hello,
I'm trying to work through exercise 2 of the Nordic Developer Academy. It has me using the Blinky Sample. When I add a build configuration I get an error. I have...
The board is nrf52840 based using mcuboot via usb, mcuboot can be activated using a switch, and is indicated via a led, all setup via device-tree, so no legacy here. Software...
Hi,
I am trying to connect nrf9160 to CMW500 callbox however I am not able to connect to it. Switching to a commercial sim card I was able to connect to the network. I am...
We are finding an issue where after a network is running for a while we are unable to interact with devices beyond connecting to them via the nRF Mesh App. Specifically, we...
HI,
I found that nrf Desktop (v2.9.0 nrf54L15) surport fwupd support, it's same with old mcuboot DFU? and i want to upgrade from SPI, how can i do? is there any demo code...
I have a few questions about the sample source of nRF5340 Audio.
1. Where does the connection processing between the Gateway and Headset take place?
2. Where is the BLE...
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-5-serial-peripheral-interface-spi/topic/exercise-1-10/
spi frequency is 1000000 in DTS...
My company is working on a project that uses the nRF53 that needs to wirelessly send out data roughly every 3ms (via ESB). We are now at the point where power needs to be...
In nrf5340 audio application( SDK2.9.0), I try to set phy to 1M in CIS( 1 gateway,2 headsets).
I made these changes：
Add in prj.conf:
In C:\ncs\v2.9.0\zephyr\include...
Hi! I am trying to get the samples "Bluetooth: Direction finding connectionless locator" and "Bluetooth: Direction finding connectionless beacon" to work on nRF54L15dk. I...
Hello,
I'm working up an application where tens of kilobytes are sent via bluetooth to a device which then stores the data on the internal flash (nrf52832). I've worked...
I want to change the Tx power in nrf5340 audio application.
I add CONFIG_BT_CTLR_TX_PWR_PLUS_4=y to prj.conf, but the power didnt change.
How to increase the power ...
I am developing a new custom board using thingy53 as a reference design. The way I programm my thingy53 now is to use the SWD debug interface with a nRF5340 DK. I understand...
