Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi
With the introduction of softdevice v2.0.1, the connection bandwidth has become configurable to be low, medium, or high; and can be specified independently for TX And...
Hi,
Now I'm using nRF52 SDK v12 and S132, I have some data(about 300 bytes)need to write to the flash. I have seen the fstorage but I donn't know how to use it. Could anyone...
Hi,
I am trying to implement a biometric group telemetry system for my gym and experimentation.
In the past I used a nRF24AP2 module and an ARDUINO PRO MINI 3.3V 8MHz...
Hii,
I want to assign name to my custom service. how can i add it i am using nrf52 chip and s132 softdevice.
I have add new service using sd_ble_gatts_service_add() A...
In my project I need to be able to get time from a continuously running RTC. The softdevice uses RTC0, and app_timer uses RTC1 (and starts and stops it).
(annoyingly I...
Hi ,
I am working on one application in which i am using UART service. Whenever i am connecting to device using nrf connect or master control pannel app, UART service empty...
Hello.
I use the BLE multilink central example to connect to 2 sensors. I changed the example in that way that i successfully connect and read data from a Wahoo Cadence...
the application is examples\peripheral\csense , cap sensor can sense my touch, but when I cover a 1mm acrylic on the cap sensor, will not sense my touch.
so I want to know...
Hi ,
We are using BLE nano board as a connectivity board and mDot board as application chip which is running on mbed platform.Connection deatsils are same as described here...
Hi,
I am working in one application in which I need SAADC to sample two channels at 1ksps and 500 samples per seconds.
I am sending 1 and 2 to switch the sampling rate...
After trying to run keil project after setting conditional breakpoit it raises error.
is it right that nrf52 doesn't support conditional breakpoits? or something wrong...
Hi,
I'm using the SDK11 and SD130 on a custom board which has a nrf51822.
I connected via SPI to a DSP that sends and receive audio.
My handler of the SPI is as it follows...
I'm trying to send a set of 246 bytes by uart fifo. I have a PC side which retreive the data, but I always miss some bytes (4 to 6).
I'm checking app_uart_put return and...
Hello,
I would like to use the nrf51822xxaa as BLE gateway for an ARM application processor (connected through the UART).
I successfully cross-compiled pc-ble-driver...
Hi..
Can i use both observer and broadcaster roles concurrently in s130 soft device..?
Is any TDMA needed to do this..?
Is it possible to do without stooping the other...
