Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi,
Does the .hex file for V7.1.0 include the master boot record? I'm writing a JLink script to flash it and I'm trying to figure out, once converted to a binary file,...
I have the PCA 10028 Board. I would like to add a characteristic on an already existing service.
In the nAN-36 I see, what is necessary to set up service and characteristic...
Dear Forum,
I just unwrapped my new nRF51 DK board and already played with some mbed example programs which worked beautifully! So first of all - thank you Nordic & mbed...
What capacitors would you recomend for this 16MHz Quartz http://www.jauch.de/ablage/med_00000848_1411137106_JXS32-180914.pdf to ensure 40ppm frequency tolerance for nrf51822...
I read the following but was not able to use it to resolve my problem.
devzone.nordicsemi.com/.../
bootloader.hex
bootloader_settings.hex
The bootloader address...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hello,
I would like to use the PCA10031 Dongle as the peripheral with the multilink examples. I will be wiring up a button to the available GPIO and using this for a space...
I want to use to set the UUID in my Nordic device as following:
Base UUID:
{0x80, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,...
hi.
I refer at the example find here link text .
i want to transmit with Advertising, as the temperature is transmitted in the example, data from some sensors .
But in...
I'm trying to port the HRS example using S110 Softdevice and SDK 7.1.0 to IAR 7.10 on the pca10028 board.
I've created an IAR project which uses the same files as the Keil...
Hi everyone,
I am trying to create a file in sd card but it is not creating.But i can read a file from sdhc card of type .txt,.c,etc with nordic evolution board nrf51822...
Hi all -
I want to use the device manager (SDK 7.1.0, SD110) to do a simple nRF51822 implementation where after the first bonding happens, and is stored in flash, the nRF51822...
Hi
I have a board with some extra bits and pieces hanging off the SWD lines.
This means the SWD needs to run at a lower speed (500kHz or less). At the lower speed, Kiel...
Hi,
I'm trying to build my IAR project but it's not clear to me what I should link against to resolve symbols referenced by the soft device headers.
Thanks,
Kenn...
Hello,
Is there any reference designs / documentation or ideas on how we can wake up NRF51 when there is radio activity on a specific frequency ?
In our design, we need...
