I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hi,
In the process of testing DFU on the hardware, I am trying to send the DFU Packets through a TTL Cable to a different pins(P0.02, P0.03. No HWFC) instead of sending...
Hi Sir
As subject, I have a nRF52-DK on hand, I'd like to use the "Bluetooth Low Energy APP" of the desktop nRF connect software to scan BLE device and connect it,
Just...
Dear community, good afternoon
We have been working with a coordinator, a router device and an end device all based on nRF52840 (Fanstel BT840F module) with nRF5_SDK_for_Thread_and_Zigbee_v4...
Hello,
I am trying edit and compile mcuboot and ultimately upload to the nrf9160.
To do so I am loading the mcuboot project using CmakeLists.txt at v1.2.0\bootloader\mcuboot...
Because the nRF52840 consumes an additional 1mA when QSPI is activated, Nordic has previously recommended deactivating QSPI when not in use, which in practice means deactivating...
Hello DevZone,
Perhip: PCA10040 SDK 15.0.0, SD 6.0.0
Central: PCA10056 SDK 15.0.0, SD 6.0.0
I am working on a BLE project and we need to make sure our link is secured...
Hi,
I am building an application for Thingy:91, currently using SDK 1.3.0. The application is supposed to collect data using BLE and forward it with LTE to the MQTT broker...
Hi,
I wanted to read all the android notification using an embedded BLE device..
I have gone through BLE_ANS example which is in nRF51 SDK, All i want is to implement...
Hi, I'm working with nRF52840DK. I need to run in Direct Test Mode, and to see RSSI & PER. I tried nRF Connect - Direct Test Mode, but it shows only the number of received...
Hi engineers,
I want to transplant demo "usbd_audio" from pca10056 to pca10100, what should I do?
I found a relevant ticket said that
Change board config.
Change...
Hello DevZone,
For a project I'm using the TAG-4 NFC writeable NDEF message example in my SDK and I had a question if this message is always stored in flash or if it is...
I have two nRF5340PDK, both of which would have worked normally. Then I accidentally download the firmware of 52840 version into nRF5340PDK by GProgrammer, which made them...
Hi,
How can I know whether the BLE link between my nrf52840 device and the pc (while connecting via NFC) or the mobile, is configured as a half duplex or a full duplex...
Dear,
I am trying to get secure serial DFU working on our custom board, which is connected to another controller through 2x UART(P0.02, P0.03, P0.30, P0.31) without HWFC...
Hi, I am developing a central application that should get data from a single or even multiple primary services with multiple characteristics in Zephyr. I am using the central_ht...
