Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi, We are using the nRF52840 in a 3V battery powered product. We have an on board 1.8V LDO regulator that supplies Vdd and Vdd_IO. We have a problem with the NFC antenna...
Dear all
I currently have a single nRF52832 SoC (custom PCB) transferring data to a single nRF51 dongle via BLE, which in turn passes the data to my PC via UART. I have...
Hi everybody,
I'm having a problem with the advertising function of the SoftDevice.
When the application starts advertising the function "sd_ble_gap_adv_start()" returns...
Hello,
We are currently looking for a way to test nRF52804 on our board with CMW500. From R&W video clip, they tested Nordic eval. board with USB connection. How do I make...
I’m interesting particularly nRF52832 and nRF52840 (with and without bootloader)
So looking at flash layout with bootloader :
is the section ‘Application data’ available...
i want to send string over eddystone tlm...and wish to use temperature part for this...so how can i display character string instead of temperature in eddystone TLM..please...
Hi, I am trying to use the iOS nRFMeshProvision SDK to create a iOS mobile application. I am trying to get the composition data but access layer always times out and gives...
Hi, I am new to Dev Zone. I am writing debounce logic and I am wondering if a button can have an interrupt set when the GPIOTE sense a HITOLO transition to fire the first...
Hello, I'm currently developing BLE_SCANNER(GATEWAY) for asset tracking or management.
My scan environment is,
[Our device -- same UUID]
The number of our beacons...
Hello. I have the same problem with https://devzone.nordicsemi.com/f/nordic-q-a/54373/uart-logging-backend-hangs-in-nrf_bootloader_app_start/220132
But this thread was stuck...
I'm trying to register a handler to determine when a system event occurs?
Previously on older design kits, I used softdevice_sys_evt_handler_set(......) to register the...
Hi,
I've managed to code an app for nRF52382 (S132, SDK14) which works properly. Also, I've taken "bootloader_secure_serial" and removed a lot of stuff to code a simple...
To the kind attention of Nordic support team,
I've just downloaded a fresh copy of nRF5_SDK_16.0.0_98a08e2.zip.
I would like to download code in nRF52810. The code in...
I want to make a programmer for nrf52832. Do you know where is the documentation of SWD is ?
Note: I found the similar question, but the links are not active
Hi
I am using Segger Embedded Studio and SDK_v15.3.0. I have a C++ code that I wish to run on the board. It has a lot of printfs. I want to see the output of the print statements...
