I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Is it possible to enter DFU / OTA from a DWT
i.e if the code crashes, and I can't trigger DFU mode by writing to a characteristic, can the WDT jump straight to the DFU...
I met this issue on some Android devices.
GATT connection is disconnected before before service discovery finished.
The issue is reporeted in following link.
github.com...
Hello, I'm using an android device to set cccd, it worked when I was running the project on nrf514xx @s110, it no longer does on nrf52840 S140, so now I wanna make sure the...
I have reformatted the code I had added earlier.
Following is the sequence of code
uart_debug_init();
gap_params_init();
services_init();
advertising_init();
conn_params_init...
NRF52832 S132 MPU6050 TWI
I want to finish the function:
When the ACC, GYRO data update, the INT pin to generate an interrupt, and then in the P026 pin configuration...
Hi,
I have the Nordic Thingy:52 (PCA20020 1.0.0 2017.19). It worked well until I downloaded new version of firmware 1.1.0 and updated Thingy. After that I didn't see advertising...
I want to use the UICR customer registers to store MAC/serialization information for my devices. It looks like the UICR customer section would be great, and the product spec...
I want to use whitelist in Central (nrf51822,SDK12),but I don't know which function to add the MAC address.
These three functions：
peer_list_get(pm_peer_id_t * p_peers...
Hi,
With S132 it is possible to advertise on specific channel.
See devzone.nordicsemi.com/.../
But, since from BLE5 advertisement can be done on any of the 40 channels...
Hardware: redbearlabs Nano V2 (see pinout below)
Programmer: DAPLink v1.5 supplied by redbear
IDE: Arduino with the redbearlab nano 2 board package
The schematic can...
I'm writing an Android application that connects to various BLE peripherals including the NRF51 and NRF52. I don't know if this question is appropriate for this site, but...
Hi,
we are trying to disable 2 of 3 advertising channels on nRF52832 SoC with the softdevice S132 (1.0.0-3.alpha) installed. The example project ble_app_beacon works well...
hi
I am using ESB_DPL protocol between 51822 and 24LE1, and i used the sdk 12.2 examples/proprietary_rf/esb_ptx.
In my case, 51822 sent some packages with PTX mode,...
Hi,
I am interested to hear if anybody knows if it's possible to use 6LoWPAN on an iOS device together with nRF52832 ? I tried searching online but have not got any hits...
