Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Is there a way to pause all peripherals when hitting a breakpoint? In particular, I would like to freeze the RTCs when I hit a breakpoint. My app wakes up once a second, and...
I`m trying to operate PWM and soft device at the same time.
I have to make 4 Mhz using PWM block so I checked the PWM driver. There is no problem when using peripheral/pwmdriver...
Hello there.
I´m using a Taiyo Yuden evaluation board with a nRF51422 to connect with 3 different sensors. In addition to that there are also 2 buttons connected to the...
I am working on a BLE peripheral. I have a large, variable length characteristic I need to set from the central.
When the central is the BTool, I can write up to the maximum...
I'm using the nRF52 + SDK11.0.0 + s132. I started with the ble_hrs example and modified it. I now want to make the service/characteristics use proprietary UUIDs and I'm following...
I have been having issues with bootloader launching my application on a custom nRF52832 based hardware device.
The bootloader itself seems to be successfully completing...
When designing the layout for my circuit using nRF52832 I've noticed that the values of CL connected to the ANT pin changed from L= 3.9nH and C=0.8pF to L=3.3nH and C=1pF...
Hello, I'm trying to generate DFU keys with the nrfutil.exe tool from Master Control Panel 3.10.0.
I always get errors....
C:\Program Files (x86)\Nordic Semiconductor...
Hi,
nrf51822 device obverse six bytes mac addres could change，when OTA failed.
six bytes mac address, five bytes fixed, one byte can change when OTA failed.
Now，my app...
Hello,
I am using Nordic Nur-10W develop kit, trying to compile NurApiExample in Raspberry Pi. I wrote a Makefile, and complie process was OK. However, undefined reference...
hi
im using sdk v6 and when i turn my board on it goes to bootloader and i can upload my program into it .
the problem is that i want it to run to my main program after...
Hello,
I would like to use a custom flash memory layout for the flash memory of nrf52:
I thought that I should be able to use the UICR.NRFFW[0] - if I set to the start...
Hi, I use PCA10040 v1.1 with SDK12.1 via S132 v3.
I use Keil 5.21.
After testing the LBS example, I was merging the NUS (NORDIC UART Service) to the standalone LBS example...
I am working with nrf51822 board softdevice of s130,sdk11.0 version.I want to create 4 KB of Flash through PStorage.I am able to create 1 kb(maximum block size ) of flash...
