Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
Hi,
I recently bought a couple of HolyIOT nRF52840 modules for a personal project (building a keyboard). I also got a JLink Edu Mini to flash/debug it. I am able to successfully...
Hello,
I've seen when ADV interval is near than 1 second, the sniffer cacth the same adv twice in diferent channels, but if the adv interval is near to 50 ms the sniffer...
Dear all,
I managed to implement custom firmware using Nordic proprietary protocol (both 1 and 2 MBPS) on nNRF-52840-DK. I would like to know if some spread spectrum tecnique...
A plain question : we are using the BLE stack with FreeRTOS based observers.
Is it possible to send to some observer an application defined event from some other FreeRTOS...
My project is a health thermometer using nRF52833. I am working nRF5 SDK 17.0.2 with GCC make complier.
I start with the ble_app_hts example and it is working fine. I try...
Hi,
I observed that in some cases SLM waking up from idle mode (at#xsleep=0) has CFUN reset to zero, even if I run AT+CFUN=1 before at#xsleep. Presumably that happens when...
My current implementation is based on light switch example and I am currently using nrf52832 kit with Mesh SDK v5.0.0. I have a mesh network setup with a client and two server...
Hello,
I am using nRF52833, nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 and SEGGER Embedded Studio for ARM 5.34.
I have imported some multiprotocol examples and trying...
I have an nRF 52832 running the SDK 15.2 with s132_nrf52_6.1.0_softdevice as peripheral and a Dell XPS 13 9350 laptop with the integrated bluetooth 4.1 module (Dell Wireless...
Hi,
can you please tell me in what cases I get this assertion?
SOFTDEVICE: ASSERTION FAILED, PCxxx: 0x12D7E
It seems to happen when a connection is active, timeslot...
HI All team Members !
Hope you all doing well ! . Yesterday , i have tested the two SDK's "ble_app_uart_c" as a BLE Beacons Scanner and "ble_app_beacon" as a BLE Beacon...
Hi,
I understand that the CoAP Client sample is configured for a public URL (californium.eclipseprojects.io) in the Kconfig file. I wanted to ask, how the KConfig file...
Hi,
I am trying to perform DFU over mesh network. I am following the steps as given in this .
I could achieve the steps from 1-6. But while running the command for Transferring...
Hi,
When running FreeRTOS I'm not able to use the NRF logger module once the task scheduler has started.
I have a low priority task that flushes the logs but whenever...
Context: nrf52840DK, s140, SDK 17.0.2
Hi,
I need to oversample a few ADC pins with burst enabled at roughly the same time periodically: e.g. oversampling 4 separate inputs...
