Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Dear All,
I am working with nRF52840 product. According to my scenario i have 1central unit(master) and up to 19 peripheral unit(slave).
I downloaded SDK 15.3.0 ble_central...
Hello, I am evaluating ways to enter the DFU mode when application is corrupted (i.e. it does not reach the code for entering bootloader).
The documentation states that...
Hi
I'm working on a IoT solution with a small circular board, 26mm in diameter. I was suggested by Johanson to use the 2450AT18D0100 antenna and a lowpass filter designed...
Hi,
I am new to this nrf development, I have been working on the SDK 15.1 on the nrf52832, with softdevice 6.1. I found these examples in the SDK very helpful. I have to...
Hi,
I am planning to send an analog signal to the nrf52840 dongle pin and send it through bluetooth to mobile app. I am thinking of merging ble_app_rscs and saadc together...
The IP mode is IPv4.
1. The hostname resolves to IP address. The resolved IP address is correct (verified with a nslookup command separately).
2. setsockopt(fd, SOL_TLS...
I am implementing a serial transmitter using the nrf_serial library from the nRF5 SDK 15.3.0. The application is very similar to a serially addressable LED string.
My serial...
Hi,
i m using my custom nrf52832 beacon.For Battery power, i used accelerometer.i trying to change advertising interval for non connectable BLE device while accelerometer...
Now there is a project, nrf52840 uses SPI to communicate with other microcontrollers. Data is currently available, but it is suspected that each packet lacks a second byte...
Using the nRF52832 device with the S132-v3.0 soft-device (s132_nrf52_3.0.0_softdevice) and SDK version 12 (SDK120200F12) (Customized for our application, which includes use...
I am working on a ble nus pheripheral application on nrf52810 with sdk 15.2 and s112. currently I can connect to nrf52 with 4 mobile phone at same time and send&receive string...
I managed to set the UUID section on my own, but I'm having trouble reading and writing some data. I'm changing the on_write function in Ble_nus.c, but I can't get results...
Hello,
When debugging one of the projects, I encountered the situation of a frequent reset of the device during connection. A quick scan under the debugger helped show the...
Hello,
I'd like to develop and base on the " Experimental: ATT_MTU Throughput Example" project.
Seems like the example project doesn't implement the DFU (aka, OAD).
...
Hi Nordic,
In my custom board, I need to access peer data at quite early stage - to determine which board it is.
So my question is: Can I call pm_init() (in peer_manager_init...
