I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Hello, I have just picked up nordic and I am running the app on Android Studio using windows, the source code I have received from GitHub so I can ticker with it. My question...
Hi everyone,
I am in the process of readying my firmware and hardware for CE certification.
The end functionality for this product is not yet finalized, but management...
I use nrf52832 board by fast advertising to connect the central(surface 4 Tablet).Then the board go to sleep.when I push the button the board use direct advertising to connect...
Hi Nordic expert:
I need using PyACI to let a nrf52832 board to send a genericOn client packet to other mesh devices those have genericOnOff server model.
My environment...
Hi friends:
I've followed "DFU quick start guide" and run DFU(from mesh-sdk-2.1.1) example done, the updating time is about 3000 seconds.
(My environment is only 2 devices...
I'm implementing my own DTM mode for the nRF52832 based on SDK14.2's DTM module (ble_dtm.c). My modified version of ble_dtm.c seems to work fine, but I don't completely understand...
Good afternoon,
I am able to write data using polling mode with the macro NRF_SERIAL_CONFIG_DEF(serial_config, NRF_SERIAL_MODE_POLLING, NULL, NULL, NULL, NULL). I am using...
Hi together!
Ist it possible to send a CR (Carriage Return) over the programmable UART Buttons?
When yes, what is the Syntax for?
For example, i need to send such a...
Hi
I used nrfutil.exe (v3.5.1 based on python v2.7.13) to create bootloader.zip file from SDK v15 - \dfu\secure_bootloader\pca10040_ble\ sample code.
CMD : nrfutil.exe...
It appears as if the LFCLK is not calibrated to 500PPM accuracy. I display the time in the system and every 60 seconds it falls 2-3 seconds later relative to the clock on...
nRF52832 / SDK V15.0.0 / nRF connect / DFU OTA Buttonless
Hello,
My device name is 21 chars but it is truncated and appears as 20 chars in nRF Connect "Discovery devices...
We are using an nrf51822 processor, running off of 2.7 volts from a switching power supply, powered with 12.4volts. The processor has simple gpio connections, and a battery...
Hi,
The structure nrfx_spim_xfer_desc_t contains both tx_length and rx_length fields.
Is there a situation where tx_length != rx_length ?
Thanks,
Daniel
I have a nicely working application that occasionally hangs. I have managed to trap a "hard fault" under the debugger (using VS with GCC). I have the system halted with the...
hello, Nordic developers!
I needs help develop rnf52840.
Goal
My goal is ble & 802.15.4 mutiprotocol, not using zboss network.
Actually, It is the same situation as...
