I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
I am following this tutorial
I'm using Segger Embedded Studio v3.10i, and SDK 12.2.0. I have the exact same problem in both Linux and Windows.
I have done everything...
What are the details of internal pin connection circuitry when connected as GPIO/IRQ vs ADC vs Comparator? Is there an internal pull down (what value)? Is there internal diode...
what should be RAM Settings for 51822QFAA chip?
I am using nrf sdk for mesh. what should be required ram settings for 51822 in order to run light switch server example....
Hello,
I have problem with missing GPIOTE event. Sometimes event doesn't occur, sometimes there is no problem. This event is very rare but important. I think it happens...
Hi all,
I am working on Temperature and Humidity(DHT11) with nrf52832, After advertising the Bluetooth i am calling the DHT11 sensor function in loop, few seconds it is...
Hello , I would like to know lifetime expectancy of NRF52832 IC. By lifetime expectancy I mean the amount of duration before NRF52832 goes non-functional. Please help me in...
Hi,
In disk_uninitialize function there are following lines of code:
if (m_drives[drv].last_result == NRF_BLOCK_DEV_RESULT_SUCCESS) { m_drives[drv].state |= STA_NOINIT;...
I have extend the light switch example to send message to the other node. I have refer This example to send message. But how to configure another node to receive the message...
HTU21D.rar hello there i am interfacing HTU21D with nrf51822. i am reading temperature and humidty from HTU21D. humidty register is E5. and temperature register is E3. now...
Hi,
I was trying to implement software UART for our product so I decided to use timer compare channels event connected to gpiote with interrupt. I want to toggle data line...
Hi,
Application: turning on/off a LED by toggling a GPIO pin using a timer and PPI. Important: the on-time of the LED must be very precise, i.e. the jitter must be minimal...
Dear Sir/Madam,
I have a sensor prototype board using nRF51822 for Bluetooth communication and I am now working on its firmware. I have installed MDK version 5.16 and...
Dear sir,
Sir i am using MDBT42V module. I want to know that whether the SCL & SDA pine are internally pulled high in this module ?
Regards,
Manoj Hiwarkar
Hi,
I have a problem where I am getting NRF_ERROR_RESOURCES errors 2 out of 3 times when sending notifications from my peripheral to my central. I think this is caused because...
I have designed a custom board with a TF325J32K7680 32KHz clock with +-50ppm tolerance, for the 32MHz I am using the CX2016DB32000D0WZRC1 with +-40ppm tolerance.
Simple...
