I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Currently i am running a BLE project on the SDK 14.0.0_3bcc1f7.
And i would like to deploy the Nordic Mesh into it.
The Mesh that i am using is from the Tutorial, which...
MS76SF2_SCH_V12.pdf Hi,
I am using SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM, NULL); for ble_Stack_init() because the off the shelf board (not from Nordic...
my company already have firmware with nRF51 and SDK11
recently, we made new Firmware
watchdog timer feature
so we modified application and bootloader
...
Howdy!
Before I break out the Segger JTAG, I thought I would try nRF Connect DFU upload. As I had a failure on OTA update there was not issue about being in DFU mode. However...
In this file: components/libraries/cli/uart/nrf_cli_uart.c
The function as defined:
static void uart_error_handle(app_uart_evt_t * p_event)
{
if (p_event->evt_type...
I have been trying to find a document referenced here 1 .
The reference reads as follows:
For more information on both modes, see sd_app_evt_wait and the nRF5 Series...
Hello there,
Finally received my 2 DK's after developing my other 2 custom PCBs and not knowing how to program them without the arduino IDE and now I'm struggling to program...
There seems to be a bit over a bug with the freeRTOS example. If you add the Scheduler to the BLE thread, Scheduler events will always be one event behind as there are only...
I am attempting to create a packet sniffer for an openthread application. I intend for it to run by sitting on the network and processing all packets with the coap_deafult_handler...
Hello there,
my goal is to wake up via NFC from POWER_OFF Mode (sd_power_system_off). Then right after the nfc wake up sending some information (e.g. UUID) via the NFC...
As a I2C master, I need to be able to read some data from a slave device the length of which I do not know beforehand. First byte I receive from slave is a packet type and...
Hi,
I want to estimate the battery life of my nRF52 device operating on a battery of capacity 800mAh. Device will advertise once in every 10sec with an advertising interval...
I print every 500ms. Here are the last few
timers:INFO:millis 510500, cnt 16728087
timers:INFO:millis 511000, cnt 16744474
timers:INFO:millis 511501, cnt 16760868
timers...
Hello,
I have measured the current consumption of the timer example of SDK13.0.0 with PCA10056.
With timer prescaler set at 16MHz i have 1.28 mA
With timer prescaler...
Hi, I got nRF52 DK PCA10040 device(s132) and follow the steps from devzone.nordicsemi.com/.../ to use arm-none-eabi-gcc(version 5.4) to build examples like blinky. I can successfully...
