Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi,
I have been working on a BLE-LTE gateway for Thingy91x for quite some time. To this end, I have tried various options: - First, using multi-image builds: modifying the...
Hi, could anyone show me how I can build nrf52840 dongles with customzied open thread library?
Right now, the nrfconnect examples in matter repo is using prebuilt open-thread...
I followed the recommendation in https://devzone.nordicsemi.com/f/nordic-q-a/124712/compile-error-trying-to-use-nrfx-nvmc-library-with-nrf54l15/550436 to use CONFIG_NRFX_RRAMC...
In section 5 of 'nRF91 Series Antenna and RF Interface Guidelines' there are a couple of circuit diagrams relating to antenna tuners, could you please provide details of how...
Hi,
I just saw the announcement for PRS support. This is very interesting to us for use cases where GNSS reception is temporarily poor. Questions:
What do we need to...
Hi Support Team
Must inductors be placed between the SW1/SW2 pins and the VOUT1/VOUT2 pins of the nPM1304? Can VOUT1/2 output normally if removed the inductors? Many thanks...
Hi,
I am working on a BLE application using the nRF5340 SoC(custom board) and Zephyr RTOS (NCS SDK version v2.9.0)
When I call bt_enable(bt_ready_cb_t cb) , Bluetooth...
Greetings, all. I'm a rank beginner here with all things Nordic but almost 50 years of embedded experience with other devices, environments, etc. I'm trying to develop for...
Custom device using nrf5340, with NFC card emulation functionality.
To use the NFC, I understand that I should use the supplied nfc_t4t library (binary) and its api. I have...
Hello, I'm developing on an application which requires to catch high speed, variable size and bursty (~0.5 Mbit/s) data from a sensor connected to a nRF9161DK trough a UART...
I'd like to use the DeviceTree Visual Editor to create the DTS for a custom board starting with only the bare device. But it seems for some reason that the DeviceTree Visual...
Hello,
I’m using the Thingy91X board (nRF5340). For my application, I need to run BLE and Wi-Fi simultaneously, so I have to increase the application size. To do this, I...
Hi I'm trying to work on OTA implementation for zigbee with nrf52840-DK boards.
there is a sample available in ncs2.9.0,light switch,but i understand it can only work as...
Hello,
I have some issues to do function an ntc thermistor with a nrf54L15DK.
An error about a wrong configuration of the adc reference or or the ADC gain appears almost...
