Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I am testing PAwR interoperability between:
TX side : third-party chipset acting as PAwR Advertiser/Transmitter
RX side : Nordic board running nRF Connect SDK...
Goal: "I am trying to get SPI3 working with a custom MAX30003 driver in a sysbuild non-secure ( _ns ) application, based on the peripheral_uart example."
Problem: "The...
Hi,
I have been evaluating the use of nrf9151 using two development kit boards.
On my first board, I set it up initially using quick start under the nRF connect app...
Hi,
The SDK version I am using is 2.6.1 and the example is "matter lock".
I wrote the following configuration into \child_image\mcuboot\prj.conf.
And add the code...
Hello, I encountered a problem while using the nrf5 SDK. In my software, I used a UART for debugging data output, a libuarte library for command output, and an app_button...
I'm trying to use nrfutil as part of a script that sets up the toolchain environment automatically using direnv .
For example:
I'd like to know how the bundle ID can...
As subject, NCS 3.0.2, I use demo 'peripheral_power_profiling' to test current on NRF52832 DK board, but the demo cound not run when power on, There is no log output, and...
Hello,
I am exploring power management on the nRF54L15 DK with nRF Connect SDK v2.8.0 (Zephyr v3.7.99) .
My goal is to:
Enter deep sleep / system off mode.
...
I am trying to wake up the NRF54L15-DK from deep sleep using RTC. The device goes into deep sleep but never wakes up. I would like to know if RTC can wake up the micro from...
Hello,
I am trying to run the wifi_scan example but I am getting a BUS FAULT error as seen below. The SDK is v3.1.0, and the SDK Toolchain is also v3.1.0.
1. Going...
i have version 0.9.2 of the nRF54L DK....
i've noticed there is now 1.0.0 documentation....
have there been any HW changes -- use of "production" MCUs, etc....
more...
Hi Team,
We are looking into the new Thingy 91 X and were wondering if it will be able to run the nRF91 Pizza Demo .
I understand the demo was originally created for the...
Hello,
I'm working on Windows 11, with the nRF Connect for VS Code v2025.5.512 extension, with ncs v3.0.2. I'm using the nRF54L15-dk (PCA10156; 0.9.2; 2025.7) development...
citing the following issues
I've been able to implement the 16 Mhz on the SPIM3. However, the incoming data on the MISO is still corrupted. With my oscilloscope I can...
Currently, we are developing our own board with NRF5340-CLAA. It does not have a 32.768kHz crystal oscillator, only an external 32MHz crystal oscillator. We have applied the...
