I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Are there any example code or API available in SDK of nRF52833 for AoA and AoD which can be use for direction finding ? i have read the white paper from Nordic semiconductor...
Hi guys !
I am working on SDK 15.2 and I have created a custom service thanks to this tutorial : https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial
...
Hi The nrf9160 product spec 1.2 states that the number of times a 32 bit word can be written is 2. I have used the nrf52840 a lot and has a similar restriction but on seeking...
Hi,
In my project, there is a lockup issue like the title. (SDK 15.3.0_59ac345)
When I try to erase flash, some data (uart command for the device)comes up through the...
Hello,
The last ticket referencing this topic is 2 years old. I thought I would ask this question since we now have NCS.
Application is a Gateway that will support Zigbee...
I am trying to fun the LTE Sensor Gateway on the Thingy:91.
The boards are missing from zephyr so I copied nrf52840_pca20035 and nrf9160_pca20035 from ncs\nrf\boards\arm...
Dear all,
I'd first like to apologize if my questions seem dumb. I'm a student in mechanical engineering and only just started getting accustomed to microcontrollers and...
Hello,
I just installed SDK and Embedded studio.
And when I try to rebuild example, error occurs.
Below is my setup information.
- SDK: nRF5 SDK 16.0.0
- Example...
Hello support,
Currently i'm working with one application using NRF52832.
in which i have to fetch data from coming from PIC controller to NRF52832 over UART communication...
Hello, I owe a nRF9160 DK version 0.8.2. The ERRATA 0.7 document says that for this version the GPS antenna does not work well. I need to use GPS for extracting PPS signal...
Hi all, I've been recently working on PSM for my device, and I've not found any resources that answer my query or provide the knowledge I need. From my reading in this article...
Hello whenever I am calling sd_power_system_off(), it gives me the following error- implicit declaration of function 'sd_power_system_off'.
What shall be the optimum solution...
I use a 3.3V battery as VDD on an nRF52832 device.
Along the line this battery might do down from 3.3V to 1.8V. Will the Internal Reference Voltage be consistent at 1.8V...
Hi,
In apply_old_config.h ,here is the code:
for example:
If I set SYSTICK_ENABLED =0 in sdk_config,here will overwrite the macro define because #if defined(SYSTICK_ENABLED...
As per the datasheet of nrf52840 any peripheral like SPI/UART/... can be configured to any of the GPIOs so is the QSPI also.
But at Pin details QSPI pins are recommended...