I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hi,
I am using the NRF9160-DK - HW issue 0.8.5 - FW version 1.0.0 and I am running the latest at_client example.
At this stage, I could get the board to work, and it seems...
Hi,
When I try to update the firmware by sending 20 bytes at a time, it fails after around 1.25 minutes consistently.
1. Is it because nrf52 cannot hold the ble connection...
We are starting to get ready for production and will have 24 board on each panel. It would be great to be able to "chain" 4 to 6 nRF52840's together using the multi-drop protocol...
Hi everyone,
I'm currently developing a potential product where I wanted to use the nRF24L01/+ to send out BLE advertisement packets for a mobile app to receive and decode...
We are using the iOS DFU SDK https://github.com/NordicSemiconductor/IOS-Pods-DFU-Library to update a device that is built against the nRF5 SDK 14.2.0. The problem is that...
Hi,
I implemented my application top of the mess 3.0, mesh is working fine able to hop the messages to the gateway via relays(nodes)
Issue with UART : -
here nrf52840...
SDK version: nRF5_SDK_15.3.0
Platform: nRF52840 DK
---
Add FreeRTOS into serial example( nRF5_SDK_15.3.0_59ac345\examples\peripheral\serial )
and I copy task of blinky_freertos...
Hi,
I want to read 4 - ADC input channels (12-bit or 14-bit) from Bluefruit nRF52832 feather using sketch code. Can you point a sample code to do this?
I could read default...
Hi,
I am currently trying to set up the HTTP Application Update Sample and unfortunately it keeps stopping at the "downloading" state. Code is exactly the same from the...
Hi,
I´m using nrf52840 with softdevice S132 and set ble_gattc_conn_cfg_t::write_cmd_tx_queue_size to larger than 1. I´m count number of queued writes by increasing a counter...
I am currently developing with nrf52832 sdk14.2. I found in the test that after opening the hid service, the connection parameters will become the following parameters after...
I encountered a scenario where I call sd_ble_gap_connect() and get an event BLE_GAP_EVT_TIMEOUT with source BLE_GAP_TIMEOUT_SRC_CONN . This is followed immediately by an event...
Hi, i have written code in android, where i am using threads to connect to 832 ble over insecure RFComm socket..
Am not pairing with 832 in my app and am directly trying...
Hi I am implementing a buttonless_DFU function right now. I decided to do Buttonless on my project's PCB Board because it is no longer an environment where I can add switches...
My setup is as follows:
nRF5 SDK 13.1 with s132 5.1.0
nRF52832_AA
Keil 5.25pre
I use RTC1 counter for timestamping along with app_timer timers. My get_timestamp() function...
