what can be the starting Point for Bachelor Thesis involving BLE 5.0 devices to be deploy in mesh Network. How the challanges in the Thesis can be address and set as a Goal...
Note: This is related to the following issues:
- https://devzone.nordicsemi.com/f/nordic-q-a/63255/nrf9160-getting-stuck-after-cell-change
- https://devzone.nordicsemi...
Hi, I am Product Manager working for Medical Device Manufacturing company based out of Ireland.
we are in search for a development house / developer who will support us...
I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hi all,
I cannot find the exact connector to use for the P19 Debug out header on the pca10028 board.
The one I have has the plastic around too big so it doesn't fit.
...
Hi,
I'm working on a simple ADC application where I sample using analog channel 1 and then read the value through the debugger. However my results are nonsense. I have...
I'm using s120_nrf51_ble_driver on PC.
To connect the BLE dongle, we need to COM port number to be known (parameter of sd_rpc_serial_port_name_set). Is there really no...
I am working on a project on wireless interface between phone and SIM card. I want to use chip nRF51822-CEAA to run SIM card simulation at phone side (include wireless communication...
in nRF51822 product specification a maximum absolute rating of 3.9 Volt is reported, while in electrical specification the maximum voltage is 3.6 Volt.
The question is :...
Hi,
I have tried with the nrfjprog tool and I get the following error:
Command:
nrfjprog.exe --eraseall --programs s110_nrf51822_7.1.0_softdevice.hex --program HILO_P_01...
Am trying to setup a module where I need to send the Serial port ( say from printer/peripheral COM)
to a BLE Peripheral/Central Module. Not sure which SOC or combination...
I have a board built which is a tracking device with a GPS and GSM modem. I'm beginning field testing and have been flashing it with a Segger then disconnecting the Segger...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
I have used the nrf8002 chip before and love it but now I am trying a different application that requires a bit more smarts. I am trying to design a system that can have an...
I have an nRF51822 board that is running fine for a while. At some point, it runs into an error and calls ble_debug_assert_handler() and goes into an infinite loop. At that...
Hi all,
I am new to nRF51822,now I want to used a simple ble application to send a data,and nRF51822 ble device read this data to control RC servo motor ,for example app...
We are using S130 v0.9 stack,
and when BLE device A is connected as peripheral of iphone
and central of BLE device B at the same time
iPhone --> A ---> B
Device...
