I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
if i use s130 soft device will it do simultaneous master/slave role.....
c1=central 1,c/p=centarl/peripheral,p1=peripheral..
assume c/p made a connection with p1 and it...
I'm using SDK 7.1, PCA10028 eval board, SD310 2.0.1, MCP 3.6.0.8331
I have an ANT device, that on a button press, it must wake up, connect to an ANT channel, and send a...
Hi all,
I am trying to connect a tablette (s110 peripheral role) to 5 S120 centrals simultaneously.
I am using nrf51822, sdk6.1, s110 v7.0, s120 v1.0.1 .
Is this possible...
So I've seen all similar issues people had where their program stuck on sd_softdevice_enable() due to the fact that ran on custom boards which didn't have external oscillators...
This are the contents of disassembly window on all optimisation levels. Program is stuck switching between two operations:
MOVS r0, r0
DCD 0xFFFFFFFF
I'm running...
We're moving our design from nRF51822 to nRF51422.
What's the difference between these IC from the point of view of PCB layout and antenna design? Are they interchangeable...
Custom Board with MCU NordicSemi nRF51822-QFAA
Softdevice S110 7.1
IAR for ARM 7.1
SDK 7.2 using a merged service (HID keyboard example + NUS example...
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
Hi,
Are there any available examples of Makefiles with JLink command integrated?
Example: "make flash" to flash the image or "make flash-softdevice" to flash the softdevice...
It's not really a question but a request to Nordic.
Could you change the #ifdef lines in gcc_startup_nrf51.s to .ifdef. So:
.ifdef __STACK_SIZE
.else
.endif
and...
Hi,
How do I determine the application address? The one that is to be programmed to UICR.CLENR0.
I have SD S110 V7.1.0 but I didn't find this information in the release...
Hello,
I receive NRF_ERROR_INVALID_STATE error quite a few times because my own state handling is still a little buggy. I want to find all these errors. What would be the...
Hi all,
Please I want to make sure of something. In the s120 specification, it's written " Bluetooth low energy combined Central and Peripheral SoftDevice", and even in...
Hello,
I need to read the UID and later on also the RSSI value of devices (Handys) in range.
It should be reading the values automatically without the need of manual connecting...
The datasheets for the nRF24LU1P ansd nRF24LO1P have near identical example antenna driver designs which vary in the values for the inductors, etc
The LU1P datasheet is...
