I feel like a crazy person looking to store large amounts of data onto an external chip that is not a micro-SD (why not micro-SD? It's power-hungry and finicky ). NAND through...
Hi
I try to run BLE HRS collector example.
when I run the project, in RTT terminal I have these error
00> sd_ble_enable: app_ram_base should be adjusted to 0x20001CD8...
Google open-sources the firmware needed to build hardware security keys
Google open-sourced today OpenSK, a Rust-based project to aid hardware vendors build hardware security...
I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
Hello,
Has there been any success with getting the python bindings for the pc-ble-driver running on openwrt? I've succeeded with the driver itself but not the bindings....
Hi Nordic Team,
In my BLE project I'm creating a Test application which gets all the advertising data from peripheral devices. The complete list of scanned device is received...
Hello all,
According to the documentation and this feedback on a case there is a maximum size for a particular cert before nrf_inbuilt_key_write returns NRF_ENOBUFS . Can...
Hi community
In order to set a reasonable CONFIG_MAIN_STACK_SIZE I'd like to have a stack usage report.
I've seen the option CONFIG_STACK_USAGE . This generates an additional...
We read 3.6 V using the ADC, for our mass production devices. The error rate is about 50% of the devices show wrong values between 3,05 and 3,4 Volts.
Even though the ADC...
Considering nRF52810 for a new project with a dead-simple application. Background:
- application is just data-pipe from mobile app to UART, both ways. No encryption/decryption...
Hi Team,
we are using the I-Jet Debugger with IAR IDE , How to load the Bootloader with this setup. Is there any additional settings required for this like Segger J-Link...
I have created code in GPIO read/write code with zephyr os. I did not add GPIO in .dts file. How the my GPIO example is working.
GPIO driver is not needed .dts support ...
Hello, All,
I am using the nrf connect tool on VS code for development, but i have a questions:
The west and some other python plug-ins used by this tool are installed...
Hello everyone. I am trying to develop a communication link between two nrf52 devices. I want to collect measurements from some sensors, pack them into a single data pack...
Hello,
I'm running Buttonless DFU successfully, but I would like to know if it is possible to start the application with the DFU service disabled, and activate it only later...
Hi, I have a firmware that runs well on nRF52833 dev kit (SDK 17.02) and I am trying to port it to a Laird BL653 dev kit. The firmware has a bootloader and it can perform...
so I use the default sdk in
D:\sdk\nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_uart_c\pca10056\s140
when i press button on nrf52840dk(pca10056)
it should at...
Hi,
I am evaluating the nRF5340 SoC and the recommended toolchain nRF Connect SDK (NCS).
I see that NCS is based on Zephyr RTOS, which provides also some drivers (spi...
Hi! I'm trying to save some variables after a watchdog reset for debug why my application hangs up.
I add a ram section on flash_placement.xml ( <ProgramSection alignment...
I am looking for Static analysis tool ( which is in compliance with standards MISRA-C and CERT-C) to be integrated with Segger Embedded studio.
Is there any preferred...
Hi
I am looking for a ways to perform DFU over serial, surprisingly i dont find any ways except this thread with no answers
https://devzone.nordicsemi.com/f/nordic-q-a...
