Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
Overview: In our board BMD340 (containing nRF52840) module present with GSM module and they exchange data using UART(PINRX-6,PINTX-7). Now we trying to use "ble_app_uart...
hi,
i am using one central and 18 peripherals. i am unable to send data to one particular peripheral from the central .plz help me to identify a peripheral in the group...
Hello, We were interested in a new SoC nRF5340, but I would like to determine some points in advance:
peripheral blocks remained the same as in nrf52840. Or were changes...
Hi there,
I would like to add the device address of a central to the whitelist on my peripheral. Is this possible without bonding? So I set sec_param.bond = false in pm_sec_params_set...
Hello.
I am working on ble project and using uart communication between bluetooth and stm32. I need to reinitialize uart module in case of any error in event handler but...
1、nRF52830。Does the dongle included with the product support the over the air packet capturing function of Bluetooth?
2、We need Bluetooth to grab packets. Do we need a third...
Hello,
nRF52840-DK
SDK: 15.3.0
s140
OS: Ubuntu
IDE: SES
Our application is has a notify characteristic that works when attached to the JLink debugger. I can get...
Hi, I am using nRF51822 on my custom board with SDK 12.2.0. I use DFU bootloader, and can update application in BLE from DFU mode with bootloader (dual bank mode is used)...
I am using the nrf52 Dk with nrf52832 chip and i want to write bulk data onto the dk and then when i read the dk from the mobile app nrf connect, i want to see the written...
Hi,
I am trying to integrate the DFU service into the ble_app_uart example. I am using NRF51822 with SDK 11. I was able to successfully run the ble_app_hrs with dfu. So...
Hi. I'm using 2x nRF52840 DK's + eero pro.
I've been noticing some stability/longevity issues with examples/thread/freertos_coap_server in nRF5SDKforThreadandZigbeev3209fade31...
Peer Manager in recent SDKs supports up to 20 peers but SoftDevice functions like sd_ble_gap_whitelist_set() and sd_ble_gap_device_identities_set() are able to handle up to...
Hi, I am trying to get BLE packages with the nRF52840 Development Kit without using Wireshark or other external app. Does anyone have any solution? Thanks in advance
I have followed this tutorial from this link but cannot get it work.
I have 3 loop. For the first loop of sending data it will have a delay about 1s and until 2 finish...
