Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello,
Thread Topology Monitor can associate an user name with a device. Where is it stored (in computer application or directly into the device) ? If it's in the device...
Hello All,
I am trying to interface an analog sensor with nrf52832, whose analog values have to be converted using SAADC and has to be sent over SPI to another chip. But...
I am testing the NR52832 using a BMD350 module on a custom made board.
Using the SPIM i faced the problem that i got an extra 500uA of current randomly. After trying to...
Dear Nordic,
We are using NRF52832 + RFX2411N for our product, and for lower the power consumption. we wonder if there has any way to know the CONNECT_REQ event.
In advertising...
After some time debugging an issue I had, I found out that my code was setting the I2C interrupt priority to 0, and at the same time that I'm running a Soft Device on my nrf52832...
Hi,
The Ch. 16 Power Supply Section of "nRF52840 Objective Product Specification v0.5" mentions the two power supply mode of nRF52840. This supply is available on the respective...
Hi.
I’m trying a multiperipheral function and have a problem.
The problem is I can not notify stable battery voltage with SAADC to the connected Central while advertising...
Hi, everyone,
We are developing BLE project on the nRF52832 chip (SDK 15.0) that must transmit to the big distances for about 20m. We set the transmission power to +4dBm...
Hi Dear nordic employee
I want to test the accuracy of my external LFCLK,
1、I enable the nordic RTC
2、set the prescaler 31（32768/32=1024），1/1024 second per step
...
The temp accuracy is stated at +/-5C. Does that include using piece-wise linear terms for accuracy? Is there any data on accuracy over a narrow temp range such as 0-40C? ...
Hei, I couldn't really find a question regarding this use-case.
I'm hoping to interface a USB (2.0) charging capability to my design and thus I need to have a communication...
Hi Nordic,
Does FDS affect PPI ADC acquisition when writing data? The test found that once the FDS is written to the data, the ADC data returned by the PPI ADC is fixed...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to ask about WDT and softdevice (centre).
The WDT setting is 2s timeout and the WDT...
Platform: windows
hardware revisions: PCA10056
nrf5 SDK: 15.2.0
mesh SDK: V3.0.0
IDE: Keil MDK \ SEGGER embeded studio
I want to use keil to develop mesh projects...
Hi, I has a question.when I start the mode of debug ,the start code execution will automatically open.I dont know why .(I use sdk12.3,and the chip IC is 52832). compile the...
