I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
i am using my custom board with nrf51822 and using sdk 12.3.0 .
the led blink example works fine on it but when i upload ble_app_uart then bluetooth is not advertising.
Hi i just get nRF52832 PCA10400 DK.
I am using SDK14.0.0. i tried to use /example/peripheral/spi.
i don't set the gpio set and high or low.in the SDK14.0.0, how to set...
Hi!
I'm using a barebones example project from SDK 12.3.0, under examples/peripheral/uart, with two versions of nRF52-DK boards (pca10056 and pca10040). The goal is to read...
Hi,
I am looking for the carrier tape spec for nRF52810-CAAA.
I am referring to the following document but nRF52810 is not listed.
nWP024 - Embossed Tape and Reel...
Hi,
I'm using a NRF52832 development kit and SDK v14.1. My application is simulating several bluetooth devices for testing purposes. The device I'm simulating doesn't support...
Dear All. I have question about compiler of nRF5_SDK_V12.3. I compile the example BLE_peripheral\experimental_ble_app_blinky by gnu arm(latest version). It can work on nRF51...
Hi,
I am having problems with a custom board using pin 0.10 as GPIO.
I have added -DCONFIG_NFCT_PINS_AS_GPIOS to my makefile. Without that, as expected, I am unable to...
Hi,
In the latest infocenter page, see:
http://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.0.0/lib_crypto_backend_micro_ecc.html?resultof=%22micro...
I am in the process of building software to drive a bare metal widget based on the nrf52840 - currently against the DK board. We have an in-house abstraction interface layer...
Would it be possible to add gatt proxy to the ble_app_uart_coexist example so it could be provisioned from the mesh app?
Or will the BLE uart service interfere with the...
Hello, I am using SDK2.0 for Mesh on nrf52840, I have not found any material related with low power mode support of nrf52840.
Is low power mode on MESH SDK not supported...
Hello!
I have been trying to make a wearable custom board. I have been trying to find some info about it but i don´t find anything useful. I have some questions. Working...
Hellou, I'm developing firware which is modification of light switch example. I have build in communication protocol, and when i receive coomand to remove nodes promisioned...
I recently downloaded nRF52840_PS_v1.0 and noticed a change in the register description for the SAADC RESULT.PTR (p. 365). A note was added that states... "Only bits 29 and...
