Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hello, I would like to get data from the advertising packet. I think that utilize this function is a good starting point :
Then ... For exemple, what do I need to do to...
HI ,All
I want to update the data at the same address in nrf52832 flash. What should I do? Do you have an example program? If you have, please send me a copy
Thanks...
Hi, I am designing a central using nRF51422, SDK V11, S130V2.0.0, modifying the central example to connect to a Ammicom BLE module of a product. After the CONNECT_REQ is sent...
Will the nRF52840 eventually support SPI speeds greater than 8 MHz? Will a preview / reference board for the nRF52840 be released with support for these higher SPI speeds...
Hi,
I am trying to set up a slave select on P0.28 but I noticed it's not driving high. I've tried several settings and I'm now using the example from https://devzone.nordicsemi...
Hi,
I am working on NRF52840 soc with SDK 15.0. I am trying to advertise beacon adv to long range. But i got to know that non connectable long range Advertisement not possible...
Dear Nordic Team,
Thanks for supporting.
hardware : PCA10028 (DK 51)
Software : SDK12.3.0 ( NUS example )
Secure DFu implement with NUS example it is compiled and...
I developed one project using BMD-300 Evaluation Kit that include nrf52832 microcontroller. In my project, I use the nRF5_SDK_14.2.0_17b948a and s132_nrf52_5.0.0_softdevice...
Hi everyone,
Using the SDK11.0.0 development product, it was found that the 52832 restarted randomly, with a reboot time of 7 days or longer.
App code condition:
1....
Hi guys!
First of all, sorry to make this question here because it is almost unrelated to Nordic, but I am desperate. I developed a device using your nRF52832. I programmed...
Hi,
I have a problem with Thread network stabilty and formation in new SDK for Thread and Zigbee 1.0. Examples seems to work fine in unchanged form, network is stable and...
Repetition of the steps followed here.
(1) Generated priv key, and public_key.c file using nrfutil, (2) generated the bootloader_settings file using nrfutil (3) Compiled...
hi!
nordic team
i am using thingy 52,and i meet a question that app_thingy_s132.axf: Error: L6405E: No .ANY selector matches accel_auto_cal.o(.bss) when i compile this...
Hello,
I am using nrf51822 with sdk11.0.0.
i observe that in while loop sd_app_evt_wait() function take much time for next interrupt to be pick.
is there any alternate...
