Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
how do i know which address is selected when i use the funtion send_reliable_message() in the example?
speciflicly in the section where is simple_on_off_client_set() funtion...
I have a question about ble_app_uart__saadc_timer_driven__scan_mode example ( https://github.com/NordicPlayground/nRF52-ADC-examples )
I flashed the project onto my nRF52...
Hi,
I would be coming out with a batch of 2500 iBeacon devices made using nRF51822. For small batches I've used an STM32 configured as a Black Magic Probe to program the...
I use the ble_uart sdk14.2.0 example, I just open the pwm, and then accept the data, I did not deal with the data received from nus, just a connection, a connection error...
hi team,
i need a clarification. my expectation is i want to transfer a image from mobile to nrf52840 pdk and display that image to the gui interfaced in pdk. my doubs are...
Hello , I'm working on the sdk 12. The problem is that when i try to do a scan of 1sec , i see thanks to the power kit that the scan is actually of 760 ms .
Can someone help...
Hello,
I am using a custom board with nrf52382 chip and mma8652 accelerometer, This accelerometer has only i2c peripherals to communicate with. I am using twi_software...
I have a tzone bt04 BLE Temp data logger,
However I'm unable to connect to it using gatttool -t random -I
I want to access it's gatt services to fetch historical data...
Hi
I just stumbled about SRAM PUF which could solve me a huge problem in IoT provisioning certificates.
https://www.intrinsic-id.com/products/spartan/ sounds very promising...
Hi,
We have an application built using sdk10 and sd110 on a nRF51822 chip using Segger Embedded Studio. The application works but it takes to long to start.
We have bootloader...
I can ping the nrf52 from pc but i can't ping it form COAP client (mozilla cooper). In wireshark i got an error that port is unreachable . What should i do ? Thank you in...
Hi,
Interface between LPC1769 and NRF51822QFAC via UART, I am fresher for NRF51822QFAC, which tool i can used, how compile source code and pleas tell me download path
I'm using the Scan and Forward mode to relay sensor data.
My requirement is for roughly 256 Bytes per message.
Question: Is it recommended to switch to a private channel...
We used Nordic default project "ble_app_beacon" nRF5_SDK_13.1.0_7ca7556\examples\ble_peripheral, running on the RF52832 DK and only enable advertisement, the interval is 10s...
Board: custom board; Mesh SDK: V1.0.0; Softdevice: S132; IDE: SEGGER Embedded; BLE: nrf52832
When I test the steps specified by “Interactive PyACI”, I can Provisioning...
