Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hello,
We have constructed a custom board of nRF52832 via I2C communication with sensor and INT based wake up. Following configuration enable
DCDC Power Enable
Disconnected...
When I was using a master slave integrated host, when I quickly disconnected the connection and then set up the connection immediately, it was found that the original disconnected...
Hello,
is there a simple example for reading out a value? The nRF5 is in this case a BLE peripheral server. The central device should only read one value at a certain time...
Hi:
I output a PWM channel in 16kHZ,i found that when i set the duty cycles 50%,my tft screen(i2c) display at a very slow speed,and it will be OK when i set duty cycles...
Hi,
I am trying to add a notification charactersitics on client, I am able to add one of them, but when i try to add another one sd_ble_gattc_write(), result is always NRF_ERROR_BUSY...
I am trying to use my nRF51 Dongle (pca10031) as a central.
I downloaded the nRF5_SDK_12.3.0_d7731ad and I could see that there is no BLE project for pca10031 (only pca10028...
i used nRF5_SDK_14.1.0_1dda907.
ANT protocol :
I used ant_background_scanning example.
I want to scannig device ID of hrm, bpwrt and bsc.
Then choose the device ID...
Looking forward to using the new sdk v15! Is there a plan to implement a new Bluetooth Developer studio plugin or should we go ahead and keep using the current version? We...
Hi, I encountered the following error in keil v5.12.0.0:
linking... .\_build\nrf51422_xxac.axf: Error: L6218E: Undefined symbol nrf_drv_gpiote_in_event_enable (referred...
Hi,
During SD+BL OTAU form SD132 ver 3.1.0 to SD112 ver 5.1.0, Old bootloader copied new one using function nrf_dfu_mbr_copy_bl(uint32_t * p_src, uint32_t len); to bad address...
Hi,
I have nrf52840 DK, I am unable to find details of which debug pin connected connected to respective controller pin.
basically dev kit has 10pin "Debug input" I want...
I tried following steps as mentioned in the tutorial, but after adding " ../../../../../../components/device " to the User Include Directories it looked like this..
But...
Hi,
I successfully installed and test pc-ble-driver with connectivity_2.0.1_115k2_with_s132_5.0.hex on PCA10040.
When I download ble_connectivity_s132_uart_pca10040.hex...
Android nRF Connect app DFU is flakey on my phone, a Motorola Droid Turbo w/Android 6.0.1. I tried with a Moto X and it worked fine, but on my Droid it rarely downloads successfully...
I'm using 52832/S132 V2/SDK11. For the test I only send notification to central just to see how many I can send in each interval. I keep calling sd_ble_gatts_hvx() until I...
