We recently encountered an issue with incompatible image partitions being pushed to in-field devices causing soft bricking. refer to this ticket for more information
Problem...
Page 399 of nRF54L15/nRF54L10/nRF54L05 Datasheet v1.0 shows:
CLK = PCLK32M/(2*PRESCALER)
but this formula does not match the values in the examples in Table 46.
I CAN...
Hello Nordic Team,
I am currently working with the nRF52832 on a custom board using nRF Connect SDK v2.9.0. I am implementing OTA DFU using Sysbuild and MCUboot with an...
Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
Hi team,
We are going to kickoff a new project of 2-mic AI recording pen. Good to see we got a very high performance for 54LM20B with DSP/NPU, which might be a very good...
Hello,
We are currently developing a Zigbee product using nRF Connect SDK v2.8.0 . While reviewing the release notes for NCS v2.9.0 , we noticed two critical bug fixes related...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
Hello Team,
I want to use scheduler to schedule two tasks i.e task_1 and task_2. The task_1 and task_2 are as follow:
void task_1() { printf("Task 1 ran"); }
void task_2...
Sorry this might be a stupid question.
We are evaluating some modem to develop a IoT device, NRF9160 comes up to our list as its tiny size.
In the design of IoT device...
I wants to use break point in project but when i set break point then 4 or 5 times working after that goes to NRF_BREAKPOINT_COND, I am using nRF52832. so guide me where is...
We are using NRF52840 and we have a watchdog timer connected to reset the Nordic, if needed. What is the minimum and maximum time need to insert a reset on Nordic?
thanks...
I want to transfer sensor data to a raspberry pi using the in-built USB on nrf52840. The example codes have the following classes: CDC_ACM, Audio, HID and Mass storage. I...
Hello,
I am just curious wether there are any specific recommendations or requirements for the package-sizes of capacitors/inductors listed in the BOMs of the nRF52840-reference...
Hello,
I am working with the latest version of nRF52 SDK 13.0.0, when I was implementing my own bootloader application, I tried to start an app timer in my code to invert...
Hi there,
Could you please tell me the exact part number of nRF9160 and nRF52840 on Thingy: 91?
I cannot find the specific information even though I looked through the...
Hi All,
How many nodes can connect to a node in ble mesh network. I go through code in ble mesh, but i did't found the answer.
Can any one please tell me.
Regards
...
We have an application using SDK for Thread 4.1. The application requires sending large custom commands over CLI.
We increased the size of NRF_CLI_CMD_BUFF_SIZE in sdk_config...
Hi, I am using the nRF connect app to test the BLE function on my code. I am able to scan the device and Service UUIDs just fine. However, when I click on the "connect" button...
Hello,
I have been trying to implement the tinycrypt ECDSA algorithm for our product. I had sampled the implementation in a sample project with ECDSA being the only implementation...
Hello I am working on an application which is based on the ble_thread_dyn_mtd_coap_cli_pca10056_s140 example. I then used the ble_app_rscs example so that I could add Bluetooth...
