Hi, On the nrf54L15 with MCU boot enabled, what is approximately the fastest time that the chip could boot and set a gpio line high, if everything not critical is disabled...
i have the nrf5833 dk board, i just started programming from quick start and it worked two times and now it does not program at all, programming failed
I'm seeing garbled/malformed UART console output when running apps on the Thingy:91 X. This includes pre-built apps from Nordic and custom apps I build myself.
Here's an...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to try out some changes that are not yet in the stable NCS releases, so I'm trying to build my Matter application using NCS v3.1.0-preview4. Unfortunately it gives...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
Hi,
Could you confirm that DeviceID found in FICR of nRF9160 is:
1/ randomly generated (64 bits = 8 bytes)
2/ they are not unique, but already on the chip when it...
Hi,
Greetings!
We have successfully checked DFU application from SDK16.0.0 and it works nicely.
We have used android nRF connect app for firmware updating.
Here we...
We have been supplied with a module that sends SpO2 data but it uses 8bit, plus odd parity. I have seen the many questions on this subject and only pose this question to add...
To be able to have USB communication/interface, do I need to apply 5V to VBUS? Or will 3V on Vdd be enough. I am planning to use coin cell that is max rated for 4.2V so it...
this is my code on DFU function, I copy to the example of experimental_ble_app_buttonless_dfu on SDK12.1. I used nrfgo studio to program s130_nrf51_2.0.1_softdevice , boot_setting...
Hi,
I've been working on Thingy:91 under ncs tag 1.2.0, trying to develop simple application using NVS just to see how it works. Based on the zephyr sample I wrote the following...
Hi:
i have some problem about using ble.
in my application has a loop:
1.use ble adv,and Wait for a while，
2.close ble adv ,and using base radio funciton.(do stop...
Hi
I was able to successfully complete the RF output power measurement using nRF52840 DK with the help of Nordic devzone last time.
Based on successful measurement...
Hi,
I use proprietary service to transmit data between raspberry pi and nRF52840 DK. The example I referred to is below.
C:\nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral...
On the nRF52840, I know the PPI, and therefore any events/tasks, are synchronized to the 16MHz peripheral clock. Here is the quote from the documentation:
"On each PPI channel...
SDK:SDK15.3.0
Example: ble_app_buttonless_dfu project.
MCU : nrf52810
SD: s112
Hi,i want to know how to reduce the ram consumption on nrf52810 sdk15.3.0 ble_app_buttonless_dfu...
My program loaded to a nRF52840 DK unfortunately adresses ports P1.15 and P1.13.
Now the DK is not reachable for Segger IDE and can not be found as a USB device.
I can...
For the connection (peripheral) tab of the online power profiler, I have a question on why if my TX payload is 216 bytes which fits within the LL PDU size, the payload would...
