Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
During testing of SDK for Mesh v3.2.0 I noticed that it's no longer possible to send a request and response using SAR where both models are on the same element. This was possible...
Dear All,
On the NRF52840 AD6 and AD4 are for USB D+ and D-, in the case I have no need to route USB signal can I use these 2 lines for General Purpose I/O especially high...
Hi
I have some questions that need your help.But it seems that there is no answer yet.The following is my questions link.
https://devzone.nordicsemi.com/f/nordic-q-a/52060...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
Hi!
I searched the devzone and there is quite few topics about how the relay is enabled / disabled in the FW... according to https://www.youtube.com/watch?v=r9CvtbCmYQY...
Hi,
I'm unable to hit my break points while using the J-link Lite debugger.
Mostly, after I've attached the debugger and reset, it goes to the correct location
FUNC_NORETURN...
Hi,
I am using the nrf51422 controller and other controller which contains Bluetooth .The nrf51422 Bluetooth is central and other controller Bluetooth is peripheral.I am...
Hi to all,
I am using nRF52832 DK with SDK 15.0 version. My two nRF52 DK damaged while debugging I am a little bit confused why this happening.
When I debugging I used...
Hi,
I need a way to dynamically disable watchdog when I do MMD debugging. I found the old trick, check bit 0 on CoreDebug->DHCSR, does not work any more in MMD. Is that...
I suspect a possible race condition happening during NUS service discoveries. I have two peripherals that are advertising and have DIS, Battery and the NUS service enabled...
Hello,
I have configured max30101 with nrf51 and I want to read the fifo of max30101. The fifo can contain 32 samples and the size of each sample could vary from 3-9 bytes...
I followed the suggestions in https://devzone.nordicsemi.com/f/nordic-q-a/51642/can-t-build-nrf-connect-asset-tracker
But, still having the same issue.
Using tag v1.0...
On one of our products, we are experiencing approximately 4% failures during production. I traced the problem to be caused by function sd_softdevice_enable not returning....
Hi Devs,
based on this example
https://github.com/NordicPlayground/nRF52-Bluetooth-Course
i was able to run it, and the value field appear below the Unknown Characteristics...
Hello Everyone, I newbie to BLE world and new to programming. Currently I am following this github repo: https://github.com/sandeepmistry/arduino-BLEPeripheral . I am using...
