Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
I successfully installed the NRF9160 DK toolchain on my linux desktop the other day using the "Getting Started Assistant" App, but when attempting to install the same toolchain...
Hi!
I'm currently evaluating Thread using a few nRF52840 DKs.
The network will be used to gather and provide sensor values.
For various reasons, I want to avoid using...
Dear all,
I have two nRF52 Preview DK boards with the SoC nRF52840. I am testing the light switch example on both boards. I have changed the light_switch_server, such that...
I tried some steps and falling back to support. I received my custom nRF52832 board and wanted to kickoff programming the board to meet my requirements. I used nRF52840 DK...
Okay, this is a fairly involved issue, so I will try to simplify as best as I can.
In short, my new Ipad Mini 5 cannot connect to an NRF52840 running the NUS peripheral...
I have just purchased 2 pcs. nRF52840 - one of them works fine - the other one reports this when i run dmesg on my linux (tested on 2 different systems) "Cannot enable. Maybe...
Hi,
I'm using nRF52832-CIAA.
VDD,Pin A7, tide with Cap 4.7uF 0603
VDD Pin H7 tide with Cap 100nF 0201
DEC3 100pF 0201
DEC2 100pF 0201
DEC4 1uF 0402
Using LDO...
So I'm kinda new to micro controllers and I followed the steps for the custom service tutorial ( https://github.com/bjornspockeli/custom_ble_service_example ), however when...
Using the scanner module, I set up a scan filter to scan for UUID with no auto connect. In the scan_evt_handler, I have a switch case for the NRF_BLE_SCAN_EVT_FILTER_MATCH...
I want to secure advertised packets using ccm
I am using s132 , SDK 14.2.0 and nrf52 dk
I found that AES-CCM peripheral is blocked by soft device usage and that I need...
I have this error.
In a last time with same error on a nRF52832 I decided this problem with increase:
On the 52832 it works. But on the 52810- project fall.
How to...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
As part of ble_evt_handler...
Hello All,
I am developing a custom board with nRF52832. All good with Segger Embedded Studio, I could download and debug the board successfully.
When I tryed to program...
Hi, i'm using nRF52840
I'm using 2 uarts :
one (uart0) is only for logging and another one (uart1) is for communication.
I can send from both uart, i can see i receive...
