Hi，everyone:
We are developing a Nearby protocol combined with UWB, which needs to communicate with the Bluetooth of Apple phones and then use UWB to measure distance. We...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Hi,
1.In ncs v3.0.0, can both USB DFU and UART DFU be enabled simultaneously on the nRF5340 DK board? 2. If USB and UART DFU can be enabled simultaneously, then how should...
Hello,
We are working on establishing a connection between one of our existing Bluetooth modules (cypress) and nordic based module to provide backward compatibility with...
Hello,
I’m working on a project based on the nRF Connect SDK v3.0.0 Matter Light Bulb sample , using the nRF52840DK. I aim to implement IPv6 support and enable Matter over...
I am trying to create a partition on my external flash using littlefs
Here is the line that is returning me an error
FS_LITTLEFS_DECLARE_DEFAULT_CONFIG ( storage ...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
Hello,
I am trying to find the IP address of the devices.
Device: nRF52840 DK
Setup: Running virtual Ubuntu 18.04 inside Windows 10 (using VMWare).
I am able to connect...
Is there any recommended way to flash the nRF51822-CEAA-R WLCSP chip?
Should a PCB design have UART design for flashing the nRF51822 chip after it is soldered on? Or should...
Hi, My problem is: When I programing my board using existing hex from SDK, I have no problem. Program working great. But if I building my own hex (build without errors) and...
Hello,
I am using nRF52832. My GPS is connected to GPIO pin (15, RX) and (16, TX) of nRF52832. My TCA9535 is connected to GPIO pin (8, SDA) and (7, SCL) of nRF52832. TCA9535...
Hi all,
I am currently building I2C communication between nrf52832 and a stm32 chip, stm32 as the master and nrf52 as the slave.
The situation is the stm32 couldn't get...
I am not connecting any uart lines to the device. But I feel the assert is being used as the timeout "handler" and then pressing button one resets the device.
I'm using...
Hi,
I'm currently going through this paper on the newest Bluetooth Mesh Standard ( http://www.mdpi.com/1424-8220/18/8/2409) . Although it's interesting to see that this...
Hi, we are using SoC nrf52810 SDKv14.2-SR3v1.2 for our RCU.
1.If there is a scenario the image transfer is finished, and the power lost happens when the old image is being...
Hello,
I am in the process of determining a system architecture for a sensor-bluetooth-android application. The goal is to read sensor information from an Android device...
I'm using Mesh SDK v2.2.0.
I want to create a new custom model,but I don't understand difference between Generic and simple onoff model.
Which model should I study?
I remember reading somewhere an article on how debugging with softdevice was going to be easier, with the debugger doing something along the lines of actually not stopping...
Hi dear nordic employee:
I use blew：
chip：nrf52832 CIAA-B00
SDK: 12.3.0
what‘s I want is same as this ， when the interrupt happen，I want to know the toggle is HIGH_TO_LOW...
Hi,
I want to develop a 4 Chanel Wireless audio system
I am using an EEPROM (without MC) to configure the nRF24.
I want to split the available band (2,4GHz to 2.5 GHz...
Hi,
I have the problem, that nrf_crypto_init() does not find any backends and thus is skipping the initialization.
What is the precondition for NRF_CRYPTO_BACKEND_SECTION_ITEM_COUNT...
