Hello,
we are using a nRF5340 with NCS 2.9 and want to signalize a
UART_LINE_CTRL_BREAK
on USB CDC_ACM to the PC.
Is there a direct way to do this?
Many thanks in...
I am analyzing the power consumption of a custom board with an nRF52833 BLE SOC and nRF21540 FEM for different BLE parameters. In one of my experiments I vary the amounts...
Hi,
I'm using an nrfx_timer event with k_poll_signal_raise to trigger a thread to perform an operation.
I've noticed around 900ms delay between when the signal is raised...
Hi,
I believe the default application on Thingy91x uses LTE-m to connect, which is working fine. How do we make it use only nB-IoT?
For Thingy91, there is a guide
Getting...
Hello.
I have a setup in which two nrf52840_dk boards are communicating through BLE. I'm using Zephyr 4.1.99.
Under heavy traffic. the board which holds the 'central'...
Is there a straightforward way to output the frequency of the 32.768kHz crystal oscillator to a GPIO pin? The motive for this request is to verify the crystal frequency without...
Hello,
I'm developing for nRF54L15 the application with the NSIB + MCUBoot. I have a problem with fprotect in mcuboot returning EINVAL error. That happens due to limitation...
Hi
Let us say I wanted to integrate mesh capability into one of the existing GATT based sample apps - like say "ble_app_hts" so that I could publish the temperature over...
Hi, i have application with buttonless DFU and boot loader. I am able to upload distribute zip package to the board via nRF Connect and nRF Toolbox apps on Android . But the...
Hello everybody,
I tested the example: https://github.com/Rallare/nrf51_ble_app_hids_kbd_consumercontrol/tree/SDK11 on my customer board (and on the DK52) with the NRF52832...
Hi,
1. After studying about power profiling and application examples/ble_peripheral/ble_app_pwr_profiling, came to know that this example currently supports advertising...
Hi,
I am establishing a Bluetooth mesh network with nordic boards (nRF52 DK) having one provisioner and many provisionee devices. But I have one doubt, if I remove the...
Hello,
We are developing wearable which has NRF52 as main MCU. We are looking for suggestions to select proper sensors like Pedometer, Heart Rate Sensor and 128x32 OLED...
Device：Nrf51822
SDK：SDK12.3
Device name consists of "scanner:" and four digits。But sometimes the device name display error。An extra character appears in the device name...
Hi,
I've undertaken my very first custom Bluetooth PCB project, choosing an nRF52810 as the MCU of choice.
Having already tried and tested a SparkFun nRF52832 breakout...
Hi all!
Antenna that used in nRf51822 developement kit:
too big for my design, so I tried to use antenna that I copied from TI AN430:
There is devices that use...
Hi,
I am following procedure to configure mosquitto using this link http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fiot_sdk_user_guides_mosquitto...
Hello,
I'm working in a bootloader based on the one included with SDK15. I want to add a timer that fires every 50 ms to keep track of time. The purpose of this timer is...
Hello everyone,
I'm new to embedded system and I'm working with the NRF52 and more precisely with the DW1001 (NRF52 + DW1000).
The Decawave device (DW1000) is already...
Hello,
I am trying to run a simple ble_app_hrs example from the SDK v12, but I am getting the same error as in this post devzone.nordicsemi.com/.../
Building ‘ble_app_hrs_pca10040_s132...
Hi,
UART and UARTE are specified in data sheet. these are separate UART or one UART and configured bt software. Please explain.
Thanks and Regards,
Harikant
