Hello,
I am using SDK v2.9.1 for a Bl653 (NRF52833) and was trying to use the Nordic Academy Example for how to setup the SPI bus. The Nordic Academy example states we must...
I'm currently working on configuring the nPM1300 used in our custom board. In the product spec v1.2, it supports 2 USB compliant current limits, IBUS at 100mA and IBUS at...
Hi,
I am currently trying to enable the GPIO output interrupt functionality on my nPM1300ek with an STM32. However, I am unable to get it work correctly(I was only able...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Hello, I am working on incorporating flash logging into an application that has a GRTC-driven EGU interrupt (capture/compare event). Here is where I am setting up the EGU...
We are experiencing some ESB link failures on the receiver end of our system: nrf54L15. After minutes to hours of use the receiver will stop getting data (we know the transmitter...
Hello,
I am developing a board with the SIP nRF9151.
I'm designing the board with a shared antenna for both the GNSS and LTE signals (Ignion NN02-224).
For the antenna...
Hello,
I have an nRF52 DK, running S132, as a client. After scanning and connecting, I use ble_db_discovery_start, which finds the devices of interest, connects, and finds...
As the title specifies, on writing to the registers mentioned, I receive a Fatal error.
Here's the test code
void save_ram()
{
__DSB();
NRF_POWER->RAM[0].POWERSET...
Hi,
I would like to know if anyone ever tried to alter the SEGGER J-Link OB Code that goes on the ATSAM3U2CA-AU IC (this is the IC that controls de PCA10040).
I'm asking...
Dear support,
I am working on some custom boards embedding the nRF52832-CIAA chip using SDK-v11.0 and s132-v2.0.1.
I have got 9 custom units and out of them only 4 work...
I asked about if NRF52 can pair to eachother without a PN532, but sounds like no, it can only read RFID tags.
So, how about if at factory we make RFID sticker/tag that...
Hi,
I need 32 bit timer-counter with s130 stack. Timer0 is 32 bits, but ble stack uses this timer. So how can i use timer1 or timer2 like 32 bit timer?
Is there any...
Do u have mobile/ios application that allows you to scan for Bluetooth low energy devices with nRF52840 and communicate with them?
If not, how we can do it?
Hi,
I am wondering which is the best method for BLE security to avoid MITM, protect the data (sniffers) and limit connection only to allowed devices for a massive number...
I am now using nrf51822 chip connected to a 50-ohm nominal input/conjugate match balun and then connected to an Embedded antenna.
I am requested to do a radio test which...
Hi,
In my project, I only have PCBs with nrf51822 chips and do not have a plan to buy a spectrum analyzer yet. But the certification requires me to apply DTM application...
The overall goal and then the specifics of what's been tried: I'm trying to utilize as much of the left-over flash space as possible to store environmental data during periods...
Hello,
I started working on mesh networking and to initiate i am looking at lighting control example . I have one nrf52dk PCA10040 which can be used as client and two nrf51...
I am working through link this tutorial and I've been able to successfully complete the steps up to D3. I'm using the bootloader_secure_ble example from SDK13 on an nRF52840...
RTT Viewer has been working great.
But is there a way to make the window buffer bigger so that I can scroll back more history?
It only saves about 80 lines.
Thanks
