Hi everyone.
I am using Visual Studio Code. When i try to compile a simple blink_pwm project, I could not. I am sending output in terminal. What is the main problem and...
Greetings, everyone, I have encountered a configuration(?) problem while trying to setup a lab for a BLE course I am teaching.
The idea is to showcase the vulnerability...
Since NCS 3.0.1 I get the following warning:
warning: Deprecated symbol DEPRECATED_UART_NRFX_UARTE_LEGACY_SHIM is enabled.
... as far as I can see I have not enabled this...
So whatever I try, the only way to get my idle current consumption to an acceptable low value is to set CONFIG_SERIAL=n in my configuration. But then I don't get printk functionality...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
Hello,
I tried to use the Cellular Monitor app within the nRF Connect for Desktop software, but it encountered the following error. I have included the relevant part of...
How can we connect the Thingy:53 to the PPK2 using the included PCA64142 current measurement board, for both Source Meter and Ampere Meter modes?
The PCA64142 board...
Hi all,
I have just buy a product use nrf51822 chip, I tried to find out SWIO and CLK pin out to flash but can not. Device only has RX and TX pin for Uart function, so I...
Hi.
I use nRF52 and I want to use DFU.
I want to make init packet because DFU need it.
To make init packet,
need master control panel.
I want to know how to get...
Hi There,
Is it possible to modify the number of BLE frames per connection interval (CI)? We are using nrf52832s and are only seeing one master request and slave response...
Hello,
can anyone tell me something about the security level of the connection like it is made in the Heart Rate Sensor Example. Is the connection encrypted or can everyone...
Hi all, I'm working on SDK11.0.0 experimental signed bootloader, I stored device type and device revision in uicr register now I need to update my bootloader through dfu and...
hi everybody.
Please help me on this
I use nRF51822 as iBeacon with ble_app_beacon in Nordic DK in below state:
only advertise in iBeacon mode
interval = 100...
Hi
Can we have both bluetooth and Gazell enabled at the same time?
We are using nrf51 series chips.
We want Gazell to communicate with with other nrf chips and Bluetooth...
I was searching the way to make example code ble_app_uart passkey pairing, while reading the documentation i found that function sd_ble_gap_authenticate() can be used to configure...
I'm trying to read a byte using uart, I'm calling app_uart_get from main loop, but it return always NRF_ERROR_NOT_FOUND . I checked with oscilloscope and I can see the frame...
Hello,
we try to use static passkey protection on our devices.
we use nrf51 sdk12 with s130.
We read a few threads for setting a static passkey like here , here and some...
Hi guys, I'm migrating my SDK 10 project up to SDK 12. There are quite a few new configuration files and setups. In order to enable app_pwm peripherals I enabled the proper...
Hello when I tried to use IronPython with MasterEmulator.dll in example as described in documentation. I got following error:
c:\Program Files (x86)\IronPython 2.7>ipy...
I'm tying to read and write external memory using Spi bus
when I flash only the softdevice and the app, the program works fine
but when I flash the bootloader, the program...
I'm trying to flash the bootloader on an nrf52 device. the microcontroller is detected successfully with segger. but then when I flash the bootloader given with sdk11 (dual...
