Hello community,
I'm currently working on setting up SPI communication between two nRF5340 DK boards , but I'm running into several issues.
SDK Version 2.9.1 : I couldn...
Hello, I just try to migrate our developing project from old parent-child build to sysbuild,
But when I build the project with non-secure cpu (with TFM), I get the <err...
Hello, the CTE signal for Bluetooth AoA (Angle of Arrival) positioning is primarily transmitted over BLE advertising channels (37, 38, 39), corresponding to frequencies of...
:
I have seen three folder in the Thread lib path, there are: ftd, mtd, master.
I have some questions below, looking forward to your answer:
For FTD, are both cli...
Hi, I am using two nRF54L15 DKs running THroughput samples.
The result of coded s8 is 52kbps, which is close to the theory number.
When I change to S2 code, the result...
Hi,
I was wondering if the newest sample available in NCS3.0.1 is already capable of holding multi connections. Otherwise, for this little time that is present i will...
Dears,
I have tried to install the nRF connect SW package on a Windows 7 32 bit system (different versions) but was not able to get the applications running. When installing...
Hello,
I am using nrf51 SDK version 10.0.0 along with the nRF51822, and I believe I have found an issue with a macro that is supposed to check the correctness of a bit...
Hi All,
Another question for those out there much smarter than myself...
We're developing an application using nrf52, sdk11 and softdevice s132 2.0.0 and have been using...
I see it is advised not to just stop a timer, but to also shut it down for certain of the nRF52s. What call is necessary to achieve this since I understand it is deprecated...
I want to read the onboard (dev board) buttons which i believe are P13-P16. I want to know the working code.
uint32_t app_button_is_pushed ( uint8_t button_id,
bool *...
I am trying to estimate the memory usage of the s132 v3.0.0 running on a nRF52832. I am interested on acting only as a peripheral with one link at a time only. From app_ram_base...
Implementing my own protocol stack with low-level programming of the radio, can I broadcast by simply programming all units to receive the same address?
No addresses (such...
Hi,
I am trying to use the sdk version 9 for the NRF51 to take ADC samples and trasmit it over BLE over UART found in the link: github.com/.../nRF51-SDK-9-0-0
I downloaded...
For example,
CFLAGS += -DCONFIG_GPIO_AS_PINRESET
CFLAGS += -DNRF52_PAN_12
CFLAGS += -DBLE_STACK_SUPPORT_REQD
Where are -DCONFIG_GPIO_AS_PINRESET, -DNRF52_PAN_12...
Hi,
I faced a strange kind of issue while i was burning the same code on nrf51442 and nrf51882 chip. The code is running fine on the nrf51442 chip but the code wasn't running...
My µvision crashed during programming and will no longer respond to trying to program it. It boots into the bootloader mode. My computer sees it but the precompiled binaries...
Hi ,
I am using nRF51 SDK with S130 soft device lib, and it is running well when downloading the example of ble_app_uart. But when I want to modify the service UUID from...
Hi,
I'd like to check the battery level in my BLE device, and I can set a timer to handle the checking, however this means that Timer 1 would need to powered up, and hence...
Hi,
The situation: nRF51 has established a connection with the iOS/Android (custom made)App. The nRF51 goes out of the Bluetooth range. Eventually, the Bluetooth connection...
I have looked around but have been unable to find doc explaining this. If there's something around, I'd truly appreciate a pointer.
I have an existing (solar powered) device...
