SOC: nrf52840
SDK: v2.9.0
Device is a central, it connected to 16 peripherals, these peripherals will power on 90 seconds and then power off 10 seconds(one cycle). ...
Hi,
I have successfully updated the firmware on the nRF5340DK controller using the DFU MCUBoot method. Now, I need to add Secure Boot NSIB to the bootloader and integrate...
Hi Support team:
I am new for using the Nordic Design kit of nRF54L15-DK.
And I would like to use the app "Direct Test Mode" v2.4.2 built-in the "nRF Connect for Desktop...
NPM2100 EK CONNECTION
Can I connect The NPM2100 EK with NRF52 DK? If so..... 1. How do I physically do this? 2. Can I program the NPM2100 EK to send Voltage Supply of 1...
I'm trying to convert some code from ESP32 to nRF, and I'm having problems with the microphone input. Mind you, I'm a beginner with nRF, so I'm sure I'm missing something...
Hi,
I got my hardware modification which added the nRF21540 to our system more or less running under NCS v2.9.0.
Currently, I have the following FEM and antenna configuration...
I'm encountering a blocking issue when trying to create a new board using the NCS Board Wizard in VS Code with Nordic Connect SDK v3.0.0. After filling in valid inputs and...
Hi All,
We are in design phase of our project . We would like to use NRF52832 for our project.
Our project is a wearable based on BLE. We are planning to use RTOS in NRF52...
I am starting to port the example
nRF5_SDK_11.0.0-2.alpha_bc3f6a0\examples\ble_peripheral\ble_app_hrs to my board. I haven't made any change to the example to save something...
Hello, I have a problem when I attempted to increase timeslot length with 10 ms ,every time I received NRF_RADIO_CALLBACK_SIGNAL_TYPE_EXTEND_FAILED signal.
Why can't to extend...
I use nrf51822qfaa,s110 v8.00,keil MDK IDE.
If the program is wrong,The chip will reset,
I want to save some data to the FLASH area before the chip reset.
What I need to...
nRF 8001: How to use it in Beacon mode where in no pairing or Bonding is required and
it only transmits some information which cn be received by any phone that comes in range...
Hi.I had been confused with parameters of sd_ble_gatts_characteristic_add( ).If I set parameters
like that:
static uint8_t ast_notify_char;
..........................
HI,
I have to implement buttonless bootloader.I am having simple doubt.I am programming softdevice,application(Hrs example with bootloader),bootloader hex file using nrfgostudio...
Hi,
I am trying to perform RF production testing using nRF51 development kit. My DUT is another nRF51 DK. I am setting my DUT according to Figure 2 mentioned in nAN 34...
HI,all
when i want to notify with MITM,there is an issue with my project.
my central role device is IPHONE and the app is lightblue .
When i enabel notify ,the nrf52382...
Hello,
I am using battery (3V) to supply nRF51822 system and the circuit is made according to DCDC mode circuit. My question is :
what is lowest voltage the battery can...
I have two p_storage_param modules param and param2 . param would store 3 blocks of 16 bytes and param2 would store 10240 bytes (10 pages). I called pstorage_register (param2...
Hello,
I followed both tutorials about using Eclipse GCC and migrating to peer manager.
I get no error when I follow them individually, i.e. when I use the project included...
Hi,
I developed an application based on s110 using the nrf51 DK and it works fine. The DK is based on a nrf51422 QFAC which is the biggest one in terms of memory sizes. Now...
Hi,
the mesh_dfu.c requires the definition of tx_config_t, which I can't find anywhere in the repo branch sdk-8-support. Same with RBC_MESH_EVENT_TYPE_DFU_SOURCE and other...
Hello,
This is in reference to the following:
devzone.nordicsemi.com/.../
The post talks about the maximum size of application that one can in order to be able to...
