i'm writing bare-metal code for the FLPR (which was loaded by a bare-metal launcher running on the M33)....
when my FLPR code "idles" using the WFI instruction, power consumptions...
I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
Hello,
I'm running an nrf52832 (fanstel module) communicating over UART with another MCU at 460800 baud. The Uarts both have matching configurations. The baud rates are...
The nRF54L15-CAAA reference designs currently show an 8 layer board which includes 2 GND layers that seem redundant and possibly unnecessary? Can someone confirm that the...
Hello,
I have working BLE peripheral_uart example based application using nRF52840 dongle with SDK v2.6.0.
I tried to upgrade SDK to v2.7.0/v2.8.0/v2.9.0.
v2.7.0 seems...
Hello,
I would like to know whether there was a way to get the name of the broadcast emitted with the sample bap_broadcast_source from a nRF5340, but directly from the...
Hi DevZone,
As mentioned in the title, the Welcome page and Application page won't show any selection for my project as following image shown.
My project is based on...
Hi,
I'd like to sample PDM at 48kHz, I'm using nRF52840 DK and nRF5 SDK.
I read a post ( devzone.nordicsemi.com/.../single-pdm-microphone-at-higher-pcm-sampling-rate)...
I'm bringing up ble_app_hrs as an eclipse project using gcc.
I'm running into an error in app_util.h, line 67:
#define STATIC_ASSERT(EXPR) typedef char static_assert_failed...
Hello,
I'm using the following setup:
nRF Connect SDK v2.9.0
B0 , upgradable secure MCUBoot, and application
Statically defined partitions in the partition manager...
I am experiencing issues configuring an SPI-based SD card interface on my nRF5340DK using NCS v2.7.0. The SD card is not initializing correctly, and I am receiving repeated...
I have two nRF52833 development boards: one is connected to the nRF21540 EK as TX (using BLE peripheral_uart), and the other is used as RX (BLE central_uart). My issue is...
Hello,
I recently updated to the "new" nrfutil tool and installed the nRF Sniffer according to the instructions. I programed the firmware and ran nrfutil ble-sniffer bootstrap...
Hi.
I am looking for help with software development for my Thingy91 project.
Project is very basic and I am ready to pay based on hour rate. It is very simple and beginner...
Hi support team,
I'm working with nRF52833 DK. installed the mobile app and desktop, but I wasn't able to connect to either.
Power switch ON, SW6 on DEFAULT. J2 connected...
Hi
The Blinky Programm only starts when I give the reset Go command via jlink commander.
At Power cycle nothing happens.
If i give the SOC an external Pin reset the...
