Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
Hi,
I have some questions regarding connecting multiple (as many as possible) BLE peripheral devices to a single central (simultaneously).
1:
Does anyone know of any...
Hi
I now is developing Android apps on the basis of NRF UART v2.0.
My s110 NRF51 device will switch two modes for differnet 128-bit UUID. These two modes have independent...
The Bluetooth 4.2 specifications allow for an L2CAP MTU size of up to 255 bytes. It looks like the CC2640 already supports the maximum MTU size of 255 bytes with a 248-byte...
Sometimes windows lose the connection to the nRF51 Dongle. The only way I have been able to reconnect to the dongle is by unplugging and replugging it to the USB port. I have...
Hello,
I am currently working on a project where I need to be able to control an RGB by writing the PWM duty cycle to a custom BLE Service and Characteristic. I am using...
When I init, uninit, and re-init a PWM with pin_polarity set to APP_PWM_POLARITY_ACTIVE_HIGH, the actual polarity of the signal is active low. This also happens when I init...
Hello,
I am getting the error code 0x3004, because I am transmitting data too quickly and filling up the transmission buffers.
From other posts, I know the solution...
I'm trying to perform OTA programming with DFU.
when I load only softdevice and bootloader I got address xx:xx:xx:xx:xx:2E
then I load the app with DFU, now the address...
nRF5_SDK_11.0.0-2.alpha.
I create peer by peer_manager.
When initializing the application, i delete them pm_peer_delete_all().
There's an application is stuck.
It works...
Hi
I have a serious problem with stability in "UART" communication over BLE.
I use the command:
err_code = ble_nus_send_string(&m_nus, &bleBuffer, 20);
where I send 20...
I have the following:
Dev board PCA10040
SDK nRF52_SDK_0.9.2_dbc28c9
Mac OSx
I was able to compile the blinky example and have the .hex in the _build folder...
I have several services on a nRF51 peripheral, and would like to have different initialization based on which service is being connected to. The related code is below:
...
Hello,
We have this board ( www.nordicsemi.com/.../nRF51822-mKIT) and would like to use P0.26 and P0.27 as GPIO (or RX/TX for serial). I've cut both solderbridges (SB2...
Hello,
I am having a lot of trouble with connection timeouts. With my current settings (10ms connection Interval and 6 seconds connection supervision timeout) I would not...
