Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
When compiling C++ code that includes ble_gatts.h you get errors like the following:
C:/....../nrf51822/Include/s110/nrf_svc.h:21:6: error: impossible constraint in...
Hi,
I can execute the heart_rate_collector example code on Ubuntu PC when driver is communicated through Segger JLink. But I'd like to use GPIO pins of nRF51-DK as communicating...
Maybe I should post my all the code here.
I want to generate two kinds of PWM1 and PWM2,used by the code as follows:
static volatile bool ready_flag;
APP_PWM_INSTANCE...
Hi everybody.
I make an application which combine ANCS and NUS services on PC100028 (nrf51 SDK 9.0.0)
This application works properly when I use IOS device which installed...
What does it mean if I set my advertising timeout with this macro (which is equal to zero)? I would expect that it would advertise forever but instead sd_ble_gap_adv_start...
The latest TWI example I can find is from 4 SDK revisions ago and uses old libraries. Is there a sample using the nrf_drv_twi library that is recommended for current development...
I'm experimenting with the relay as well as hrs and rscs demos. Basically, I want to check at startup for IRKs stored in flash on startup in the peripherals. I'm only working...
I have developed my custom board and my custom application based on nRF51822 and S110-v8.
It perfectly works with Master Control Panel v9.0: connection, bonding, dfu,......
Hi,
I am interested in your nRF51 IoT SDK, IoT SDK for applications using IPv6 over Bluetooth Smart.
The presentation www.youtube.com/watch describes an architecture...
I'm developing an application supporting concurrent central and peripheral connections and using the new Connection State module in SDK 10 to decide whether a BLE stack event...
Are there any modules/devices with sar certification for the nrf51?
I have a need for something that will be placed with an elastic band against the arm or upper torso...
Hello,
I am using S110 8.0 stack and 9.0 SDK and I am testing the signal strength.
Now I am able to get the BLE_GAP_EVT_RSSI_CHANGED event after I started performing rssi...
Hello,
I am investigating the on_ble_ev function and trying to get back the Connection Interval parameters set by the Master Control throught the ble_evt_t struture . Is...
Hi,
I want to use the NRF51-DK to program an external device. It worked fine so far using the J-Link Firmware. I had to switch to mbed since it is a huge mess to get it...