Hi!
I have been unable to find a single, simple set of instructions for adding MCUboot to a project(toolchain 3.0.0 sdk 3.0.0) that will enable a non-default signing key...
Hi everyone,
We're using the "Manufacturer Specific Data" field within its advertising packets to send the firmware version to a phone application. It requires the company_indentifier...
Hi, I am using ncs 3.0.2 and an looking at adding extra .conf files during production. For the app it works fine using --extra-conf, but I can't figure out how to add one...
Hi All, I am trying to write to "adafruit e-link 2.13 Featherwing colour dispaly" from nRF54L15DK running zephyr. With ESP32 i am able to write to the display. But with nRF54L15DK...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
Hi nordic:
Project MCU: NRF54L05; Development Platform Version: NCS 2.9.0. The APP occupies 220KB of space. adding MCUBOOT and Create an pm_static.yml file in the project...
We are currently using Zigbee Firmware built with nRF Connect SDK v2.7.0 on the nRF5340.
We plan to upgrade the nRF Connect SDK to v2.9.2 and use the Zigbee Firmware built...
I want to send a data of length 1024 bytes over the ble UART , but the maximum length of data is 20 bytes at a time. Is it possible to increase the data length per instance...
Hello!
I try to use "ble_default_bootloader_app.hex" with my app to allow OTA option for my device. (nrf51822 and SDK 7.2.0) With NRFToolbox I can connect to the device ...
Hi all,
How can it be that sd_ble_gatts_sys_attr_set function returns BLE_ERROR_GATTS_SYS_ATTR_MISSING?
With the first and second connect it returns success but the...
I saw that each CCCD or sys_attr should be persisted per connection, does it mean it should be saved on flash to be restored during next connection for same device ?
and...
If iOS of BLE master sends 4 packets of the same write characteristics with MD bit in the same connection event, how does SoftDevice of BLE slave work?
The ble_event_handler...
Is there a summary of potential pitfalls, i.e. issues which are asked repeatedly by users in these forums regarding HW/Schematic/PCB design for NRF BLE chipsets. Making mistakes...
I just published my port of a new FreeRTOS operating system version for the nRF51x22 and the nRF51 SDK 8.x.x to github.com/.../freertos_nrf51 , the README is copied below...
I am trying to implement some write to flash, and started by integrating the relevant functions from the example code I found in this thread .
I added a dummy write function...
Hello,
I'm building an aplication with multiple nRF51822 beacon modules. I'm using dual mode S130 softdevice. Sometimes, when beacon recieves a lot of messages, and forwards...
I'm trying to erase the page 32 of a nRF24LU1+ via SPI (using a Bus Pirate).
What I did so far:
Display the first 16 bytes of content of page 32: 0x03 0x40 0x00 0x10...
I have a switch connected on the nRF51DK Board. The switch is connected on PIN25 and PIN 28. I try to read the state of the switch.
My setup:
-nRF51DK
-SDK8.1
...
Hi
I am making some low-power wireless sensors powered by coin cells, which will sleep for long intervals between readings/transmits. I am using the micro ESB libraries...
Whenever I try to burn program to external nRF24LE1 with ISP interfacing from nRFgo Starter kit using nRF Studio, I am notified that chip on board couldn't be detected. I...