I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to try out some changes that are not yet in the stable NCS releases, so I'm trying to build my Matter application using NCS v3.1.0-preview4. Unfortunately it gives...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi,
I want to implement stack tracing to check stack overflow and remaining stack. I followed the implementation given in example github.com/.../memory_watcher.
Memory...
Hi
I am coding a s130 NUS example.
The base example is sdk8.1.0 ble_app_uart peripheral example.
I added central part from Github sdk8.0.0 ble_app_uart_c...
Hi
I've installed the new tools in version 7.5.1 to support the new nRF52 family. While working on the nRF51 again i found out, that the old parameters i used for programming...
Hi,
I'm working on a project where nrf51 modules should communicate with each other. For that i'd need to set characteristic that can store string. Now i've done that ...
Hi,all.i call function "sd_clock_hfclk_release(); power_manage();" and want my device to sleep.as this,my device's current is 2.2mA.what's wrong ?Can someone help me?
I have a master device using SPI interface , write data to nordic SPI salve and send data to cell pohone.
But ,the master device SPI wirte data is fast, the nordic will...
hi all,
since i am new to nRF24L01+ device, kindly any one provide me details regarding range that can be supported by nRF24L01+ device.i already try to find out information...
Hi,
I am attempting to create a secure BLE connection in security mode 1 and level 3.
I noticed that when I simply call sd_ble_gap_authenticate with MITM = 1 it seems...
Hi,
I would like to save the most energy when going to sleep mode. In particular, I want to turn off the radio while keeping just RTC timer on.
So, after shutting down...
Hi there,
When I tried to send data chunk (it's about 8K) to phone side according to this , the speed is much slower than 1K/s, and what's more, it's disconnected with...
Hi,
I have a problem in CRC of setup message for nRF8001,
and I already try the CCITT-16 algorithm with below conditions:
Poly = 0x1021,
Init = 0xFFFF,
Ignore all...
Hi,
I want do RSA on NRF51822. The build environment is GCC. And the develop base on S120. The RSA need 1K to do calculation. If I enable the RSA calculation, the APP may...
Is there any high-level documentation of the nRF52-DK (PCA10036) connections?
Studying the schematics, I have inferred some of the intents, like:
built-in JLink automatically...
Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
Hey,
I'm working on integrating nrf8001 with STM32, currently trying to write my own stack.
Upon reset, I read the DeviceStartedEvent, 0x81 and it shows "0x02 0x00 0x02...
