Hello, I wanted to update my project (Custom board using the nRF54L15 ) to the v3.3.0 SDK since this fixed a BLE bug with the v3.0.1. version. To my knowledge I did not change...
I have installed ncs3.3.0 and want to keep ncs unaffected. According to the document docs.nordicsemi.com/.../sdk_setup.html , I should choose to import the edge impulse SDK...
Hi,
nRF9151 + Kyocera AVX P822601 internal SMT antenna: 8 dB RSRP loss vs external antenna — possible PCB layout issue?
Test Results
Test 1 — Out of Faraday cage, internal...
In our product, we use Laird (Ezurio) BL653 BT module. In some countries such product requires SRRC certification. For SRRC certification we set BL653 to DTM mode with AT...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hello,
We are currently evaluating BLE Gateway (CIS, BIS) development using the nRF5340 Audio DK.
We would like to ask whether bidirectional CIS streaming is officially...
Hi, I was checking the HAL for SPI in master mode and notice that when pm_device_action_run(<spi_device>, PM_DEVICE_ACTION_SUSPEND); the CS pin isnt changed since it status...
I want to migrate my project (for a custom nrf5340/nrf7002 board) from NCS2.9.0 to NCS 3.2.0, to hopefully get the wifi WPA Enterprise functionality to work. This is an existing...
I switched from the nRF-bm\v0.9.0 to nRF-bm\v1.0.0 SDK and now I am getting the following error message:
fatal error: nrf.h: No such file or directory
"nrf.h" is now located...
Hello, I'm using Nordic Central HR example. I'm wondering how to read RSSI of a BLE device connected to the NRF5340, I have tried multiple version found on this forum, but...
Howdy,
I am trying to connect a Waveshare BME280 to my nrf9160dk, and it's not obvious which jumper goes where. The documentation states:
Wire color
Sensor board...
hi,
i'm new with the nrf9160DK so can you please guide me to how can i start and config my nrf9160Dk with my laptop from scratch because this video is not helping me https...
Hello:
I created an app.overlay. Here it is:
/ { aliases { fra_sw = &fra_sw0; }; fra_sw0: fra_sw0 { gpios = <&gpio0 0 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>; label = "FRA_SWITCH...
Hello,
We have a dual-purpose connection in our design where the signal can be either an analog input or a digital output. We have done some testing and can see that we...
Hi and Nordic forum
Please find the attached summary on the issue we are facing and help us get the guidance regarding the same
We are developing a Zigbee-based device...
Hello,
I am evaluating the nRF54L15DK current consumption based on Nordic example: https://academy.nordicsemi.com/courses/nrf54l-series-express-course/lessons/lesson-5-development...
Hi everyone, I'm thinking about implementation of SWD-over-USB with proper DAM (both CC1/CC2 pulled high). It is not totally clear to me what would be default nPM's behavior...
Hi all,
I've been troubleshooting my 9151 feather and have run into some issues with very specific AT commands. I'm trying to connect to an MQTT broker through AT commands...
Hi. I have a question about the selection of Host IC of nRF7002.
Looks like general official recommendation is nRF5340.
But my team has a long history with nRF52840...
Hi,
I'm trying to use the connection manager in my application, but it never connects or shows any events. I've tried using the https_client sample as well, but that gives...
After 9 years of work I have finally finished my product and it is FCC and EU certified, and ready for a pilot production run.
I would like to copy and paste my PCB design...
