The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
Hello,
I could use some guidance on where to look for a power draw that I am not understanding. I am not a hardware engineer but have been tasked with completing firmware...
We experienced an issue in production, in which about 40% of boards had excess current consumption by about 75uA. Root cause was found to be the PIN_CNF of a GPIO pin. During...
Is there any way that a BLE event handler installed with NRF_SDH_BLE_OBSERVER, can stop the execution of other (following) observers?
I have various modules using their...
Hi
I am a student and this is my first project working on BLE. Please keep that in mind.
The end goal is to create a fingerprinting system with a Thingy (nRF6936) as...
I have modified the BLE app Blinky example so that the LED is enabled (state 1) on power up. However, this is not being reflected on the BLE side because when I connect with...
Hi, when debugging, I'm encountering this problem where relevant SPI registers (likely status registers) signaled a successful read before the actual data could be pulled...
We're developing a mobile application which will communicate with a satellite antenna over BLE. We will not have access to the antenna for a few months, and therefore we aquired...
I am using the UART to perform serial DFU on nRF52832. I got it to work fine using nRF Connect SDK 1.8.0.
Now, I need to pass some serial data to the APP when not in DFU...
Hi, I have to develop a new nRF5340/Zephyr/MCUBoot-based device that communicates with a Windows application via USB. The Windows application already manages other legacy...
Hello,
I'm trying to implement a set up of the ble device name from the NVMC UICR register.
But when I try to take it from the register and to set it has a name, it doesn...
Hi,
when using the spi peripheral in slave configuration, what can I expect at power consumption level? does the spi peripheral derive its clock from an internal system...
Hello,
I am using nRF52840 DK's P20 SWD to communicate with an external nRF52840 board . My setup works fine with nrfjprog running from command line. To communicate with...
Is there any example code using a QSPI image as the input for the bootloader instead of e.g. BLE? What format does that have to be in to begin with? Currently doing DFU updates...
Hello friends
I am fresher for Nordic semiconductor . I want to interface triaxial accelerometer of 15MHZ frequency with nrf52840 with inbuilt ADC and transmit the data...
Hello,
I will try to use the macro ZB_ZCL_SET_MODIFY_ATTR_VALUE_CB to define a callback when an attribut is written in my device. But the callback I write is never called...
